User manual REVOX B77 SERVICE INSTRUCTIONS

[. . . ] You will find more information about addressing the M203 in the side room, on Page 6 of this manual. You can download the new Multiroom Planner V2. 00 free-ofcharge from the download area of the Revox Homepage, under www. revox. com. 1 Introduction M203 Switching between stations using the Revox wall-mounted keypad* The M203 offers the option of selecting specific stations using the skip keys (<>) on an M218 wall-mounted keypad, once the TV tuner has been selected. This comfort function requires two settings: Note: Monitor-only devices This comfort function is only available with TV models with an integrated TV tuner. It cannot be selected in case of monitor-only devices without a TV tuner. 1/2 Audio IN assignment 2/2 TV Tuner assignment M51 in combination with M203 The sound input, e. g. [. . . ] Connection: M203 with IR controller Socket: IR-Link Setup: M219: Yes M203 The connection to an IR receiver or a wall-mounted remote control is done through the 3pin, screw-fixable Phoenix plug connection. Revox recommends the use of a 2-core screened cable (microphone cable), where the screening is used as ground. This cable may be a maximum of 30 metres in length. Please ensure that you use the correct polarity when setting up as otherwise you might damage your equipment. 20V (DC) IN IR Signal Ground The maximum number of IR receivers that can be switched in parallel per M203 is 3. 5 Installation & Connection M203 Setup key Setup #1 Function: Display: Connection: M219: a) Slot M51 Addr. assignment Slot Address M51-Link Yes M51 operation (fig. page 11) A different address must be assigned through the slot address, if a second M203 (M200) is connected to the M51 Link output, so that both don't occupy the same slot address. In the case of a double address assignment, neither of the two M203s (M200s) would be shown in the Version list. Slot address: #11 or #12 The two slot addresses 11 and 12 are available for selection. The following message appears if the selected address is already assigned: Using the Setup key, you call up the M203 menu, which is shown in the M51 display. If the M203 interface is connected with an M219 Additional room amplifier, the M51 display is also used. Please also refer to the picture on the next page. If you now select the source SAT (Optical) at the M51, the Revox TV automatically transmits the SAT receiver picture over the Input YC and the sound from the SAT receiver is transmitted over the M51. Yes You should always carry out a complete reset with each new configuration as well as when changing to another TV model. To do this, press the Disable softkey on Setup page #2 and keep it pressed, until the system automatically returns you to page 1. No A complete reset is not necessary with an assignment change within a TV model. 10 Installation & Connection M203 Connection plan: Revox TV with M51 A Connection plan: Revox TV with M219 11 Installation & Connection M203 Connection plan: Gefen HDMI switcher with M51 A Note The HDMI output on the M51 is only available if the DVS module is installed ® Gefen : Registered trademark of the Gefen Company/US 12 Installation & Connection M203 Connection plan: Gefen HDMI switcher with M51 13 Installation & Connection Gefen HDMI Switcher 4x2, 4x1 Switcher 6x2 Control software for the HDMI Switcher from the Gefen Company (www. gefen. com) The HDMI inputs on the HDMI switcher are activated, dependant on the M51/ M219 source. If there is no assignment, the HDMI input that was last selected remains active. Setting is done on page #2 in the M203 Setup Product features: - 4 HDMI inputs (4x1, 4x2) - 6 HDMI inputs (6x2) - 1 HDMI outputs (4x1) - 2 HDMI outputs (4x2), whereby both outputs can be operated in parallel - Resolution up to 1080p - HDCP-enabled - Optical audio digital output A crossed Sub-D cable is required for the transmission. Connection type: Plug-Plug For this reason, you should use the enclosed crossover adapter and gender adapter with the supplied Revox cable. M203 9-Pol Pin 2 Pin 3 Pin 5 9-Pol Pin 3 Pin 2 Pin 5 Max. This guarantees that important 2 minute run-on phase of the fan is always adhered to, even when an operation was carried out that would have bypassed it. M710 Projector switching times: Power-OFF 10 sec. Alternating source* Autostandby : ON Changing DISC From DVD to CD 60 sec. 60 sec. Plasma-TV 42 HD * Turning from a video source to a pure audio source. 16 Configuration M203 Setup #2 ­ AV Assignment Function: Display: Connection: M219: AV Assignment Source RS232 Yes 1. Selecting audio source To start with, select the M51 / M219 audio source that later should activate a particular video input on the Revox television/ HDMI Switcher, using the Source ± softkey. Unknown audio sources "Sources unknown" can still be present during the initial configuration, caused by the swap or the de-installation of modules. Following switch-on, it can take a few seconds until the M203 interface has identified all the M51 / M219 sources and until the Source "Unknown" message disappears. Any remaining unknown sources should be deleted by pressing the Disable softkey twice and then pressing the Delete softkey. [. . . ] The following display appears, if a video input is called by one or more audio sources: Assignment example As the televisions that can be selected from have different video inputs, only those video inputs that the corresponding TV device has, are actually displayed. The softkey Store appears as confirmation each time the Input is changed. Press Store if you want to save your changes. Otherwise the original setting is retained. This example shows you that, as well as the currently displayed audio source (DVD), a further audio source has also been assigned to this video input (here YUV). [. . . ]