User manual RICOH AFICIO 1106EX

[. . . ] Operating Instructions Copy/Document Server Reference 1 2 3 4 5 Placing Originals Copying Connect Copy Document Server Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. [. . . ] C Set a binding margin for a front page. Press [] and [] when setting the left and right margins, and [] and [] when setting the top and bottom margins. D Set a binding margin for the back side pages. Press [] and [] when setting the left and right margins, and [] and [] when setting the top and bottom margins, and then press [OK]. Margin on the back side of the page is valid when [1 Sided2 Sided] or [Combine 2 Sides] is selected. E Place the originals, and then press the {Start} key. Note You can set the binding margin up to 30 mm (1. 2") in 1 mm (0. 1") steps. If you make a mistake, press [], [], [], [], or press [Clear] to set a new value. If you do not need to specify the margins for the back side pages in step D, press [OK] and proceed to step E. Reference "Edit", General Settings Guide 97 Copying Erase You can erase the center and/or all four sides of the original image. This function comes in the following modes: 2 Border Erases the original's edge margin from the copy. Center Erases the original's center margin from the copy. Center/Border Erases both the original's center and edge margins from the copy. Inside Erases a designated area of the copy image. Outside Erases all areas of the copy image other than the area you have selected. 98 Copier Functions Note The relationship between the original orientation and the erased part is as follows: L original K original 2 Erased part B 2-99 mm (0. 1"-3. 9") The erase width is set to 10 mm (0. 4 inch) as a default. You can change this setting using the Edit menu in Copier/Document Server Features. Reference "Edit", General Settings Guide A 99 Copying Border Erase (same width) This mode erases the edge margin of the original image. A Press [Edit]. 2 B Press [Erase Border]. D Set an erase border width with [n] or [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [OK]. F Place the originals, and then press the {Start} key. Note To change the value entered in step D, press [n] and [o] to set a new value. 100 Copier Functions Border Erase (different width) This mode erases the edge margin of the original image. A Press [Edit]. 2 B Press [Erase Border]. D Press the key for the border you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [OK]. F Place the originals, and then press the {Start} key. 101 Copying Center/Border Erase (same width) This mode erases both the center and edge margins of the original image. A Press [Edit]. 2 B Press [Erase Cntr/Brdr]. D Press [Center], and then set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [Border], and then set the erase border width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). [. . . ] · If Blank mode is selected, the designate sheet is not counted as a copy. Slip sheet · Tab stock are possible to use as slip sheets. · If you do not copy onto slip sheets, they are excluded from the number of copies counted. 5 206 Supplementary Information Connect Copy Important Do not use the connecting cable with other equipment. Always turn off the main power of the main and sub-machines when before disconnecting the cable. [. . . ]