User manual RICOH AFICIO 1350

[. . . ] Operating Instructions Copy/Document Server Reference 1 2 3 4 5 Placing Originals Copying Connect Copy Document Server Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. [. . . ] Erasing the image on the back is valid when you copy 2-Sided originals. E Press [OK]. F Place the originals, and then press the {Start} key. Note To change the value entered in step D, press [n] and [o] to set a new value. 100 Copier Functions Border Erase (different width) This mode erases the edge margin of the original image. A Press [Edit]. 2 B Press [Erase Border]. D Press the key for the border you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [OK]. F Place the originals, and then press the {Start} key. 101 Copying Center/Border Erase (same width) This mode erases both the center and edge margins of the original image. A Press [Edit]. 2 B Press [Erase Cntr/Brdr]. D Press [Center], and then set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [Border], and then set the erase border width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). F Press [OK]. G Place the originals, and then press the {Start} key. 102 Copier Functions Center/Border Erase (different width) This mode erases both the center and edge margins of the original image. A Press [Edit]. 2 B Press [Erase Cntr/Brdr]. D Press the key for the order you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. E Press [OK]. F Place the originals, and then press the {Start} key. 103 Copying Inside Erase A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). You can input lengths of 0 ­ 432 mm, 0 ­ 17". 2 B Press [Edit]. D Press [Erase Inside 1] ­ [Erase Inside 5]. [. . . ] · If Blank mode is selected, the designate sheet is not counted as a copy. Slip sheet · Tab stock are possible to use as slip sheets. · If you do not copy onto slip sheets, they are excluded from the number of copies counted. 5 206 Supplementary Information Connect Copy Important Do not use the connecting cable with other equipment. Always turn off the main power of the main and sub-machines when before disconnecting the cable. [. . . ]