User manual RICOH AFICIO 5500 SP

[. . . ] Operating Instructions Copy/Document Server Reference 1 2 3 4 5 Placing Originals Copying Connect Copy Document Server Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. [. . . ] Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. F Press [OK] twice. G Place the originals, and then press the {Start} key. 96 Copier Functions Center/Border Erase (same width) This mode erases both the center and edge margins of the original image. A Press [Edit / Stamp]. 2 B Press [Erase]. F Press [Center], and then set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. G Press [Border], and then set the erase border width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). H Press [OK] twice. 97 Copying I Place the originals, and then press the {Start} key. Center/Border Erase (different width) This mode erases both the center and edge margins of the original image. 2 A Press [Edit / Stamp]. B Press [Erase]. F Press the key for the order you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (0. 4 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. G Press [OK] twice. H Place the originals, and then press the {Start} key. 98 Copier Functions Inside Erase A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). You can input lengths of 0 ­ 432 mm, 0 ­ 17". B Press [Edit / Stamp]. 2 C Press [Erase]. D Press [Erase Inside 1] ­ [Erase Inside 5]. E Enter the value of [X1] with the number keys, and then press [q]. F Enter the value of [Y1] with the number keys, and then press [q]. G Enter the value of [X2] with the number keys, and then press [q]. H Enter the value of [Y2] with the number keys, and then press [q]. If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. I Press [OK]. K Place the originals, and then press the {Start} key. If you want to go on to erase another area, repeat from steps D to I. 99 Copying Outside Erase A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). [. . . ] See "Tray Paper Settings", General Settings Guide. Designate · When "Combine (1 Sided2 Sided)" has been selected, specified pages will always be copied on the front of copies in the same way as in Chapters mode. Slip sheet · If you do not copy onto slip sheets, they are excluded from the number of copies counted. 5 201 Appendix Connect Copy Important Do not use the connecting cable with other equipment. Always turn off the main power of the main and sub-machines when before disconnecting the cable. [. . . ]