User manual RICOH AFICIO 7000

[. . . ] Operating Instructions Copy/Document Server Reference 1 2 3 4 5 Placing Originals Copying Connect Copy Document Server Appendix Read this manual carefully before you use this machine and keep it handy for future reference. For safe and correct use, be sure to read the Safety Information in "About This Machine" before using the machine. Introduction This manual contains detailed instructions and notes on the operation and use of this machine. For your safety and benefit, read this manual carefully before using the machine. Keep this manual in a handy place for quick reference. [. . . ] If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 F Press [OK] twice. G Place the originals, and then press the {Start} key. Center Erase This mode erases the center margin of the original image. A Press [Edit / Stamp]. B Press [Erase]. D Press [Erase Center]. 97 Copying E Set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 F Press [OK] twice. G Place the originals, and then press the {Start} key. Center/Border Erase (same width) This mode erases both the center and edge margins of the original image. A Press [Edit / Stamp]. B Press [Erase]. E Press [Same Width]. 98 Copier Functions F Press [Center], and then set the erase center width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 G Press [Border], and then set the erase border width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). H Press [OK] twice. I Place the originals, and then press the {Start} key. Center/Border Erase (different width) This mode erases both the center and edge margins of the original image. A Press [Edit / Stamp]. B Press [Erase]. D Press [Erase Center/ Border]. 99 Copying E Press [Different Width]. F Press the key you want to change and set an erase width with [n] and [o]. Pressing [n] or [o] changes the width in increments of 1 mm (0. 1 inch). Pressing and holding down the relevant key changes the width in increments of 10 mm (1 inch). If you select to erase the image on the back of the original, press [2 Sided Setting] and [Back]. Erasing the image on the back is valid when you copy 2-Sided originals. 2 G Press [OK] twice. H Place the originals, and then press the {Start} key. Inside Erase This mode erases a designated area of the copy image. A Specify the point where the machine starts scanning (X1, Y1) and where it stops scanning (X2, Y2). You can input lengths of 0 - 432 mm, 0 - 17". B Press [Edit / Stamp]. C Press [Erase]. D Select one of the areas from [Erase Inside 1] to [Erase Inside 5]. 100 Copier Functions E Enter the value of [X1] with the number keys, and then press [q]. 2 F Enter the value of [Y1] with the number keys, and then press [q]. [. . . ] · Tab stock is delivered face down regardless of its paper weight. 5 198 Supplementary Information Connect Copy · Do not use the connecting cable with other equipment. · Always turn off the main power of the main and sub-machines when before disconnecting the cable. Otherwise it might lead to malfunctioning of the two machines. · You can store on a program whether or not to use Connect Copy. [. . . ]