User manual RICOH C410DN Installation Guide

[. . . ] Quick Installation Guide Read this manual carefully before you use the product and keep it handy for future reference. For safe and correct use, please be sure to read the Safety Information in "Safety Information" before using the machine. CLP30DN/CLP27DN/C7531dn/C7526dn/LP231cn/ LP226cn/Aficio SP C411DN/Aficio SP C410DN Where to Put the Printer The printer's location should be carefully chosen because environmental conditions greatly affect its performance. Optimum Environmental Conditions Permissible and recommended temperature and humidity ranges are as follows: Checking the Contents of the Box Follow the procedure below to verify the items that come with the printer. Unpacking To protect it from shock and vibration during transit, this printer comes packaged in cushioning foam and secured with tape. Remove these protective materials after bringing the machine to where it will be installed. Turn the two green levers counterclockwise ( ), and then slowly open the inner cover ( ). Remove the protective sheet, as shown. Pinch the orange tape, and then pull it out. Warning · Confirm that the wall outlet is near the machine and freely accessible, so that in event of an emergency, it can be unplugged easily. [. . . ] · If toner gets on your clothing, wash with cold water. Hot water will set the toner into the fabric and may make removing the stain impossible. LOADING PAPER AET133S Load the new paper stack print side up, making sure the paper is flush against the paper guides. Adjust the paper guides to close any gaps. · Make sure the power cable is plugged securely into the wall outlet. · Turn the power switch off when plugging and unplugging the power plug. Turn the power switch to " "On. AET032S Be sure to read the label, which is attached on the front surface of the printer. This warns you that ink-jet paper cannot be used with this printer. First, install the yellow toner cartridge. Holding the toner cartridge horizontally ( ) with the locking lever on the upper side, install the toner cartridge bottom first, and then move the locking lever to the triangle mark ( ). The following describes how to load paper into the standard paper tray (Tray 1). Caution · Do not pull out the paper tray forcefully. If you do, the tray might fall and cause an injury. AET044S · When you first use this printer, use the four toner cartridges supplied with the printer. AQC028S · The toner cartridges that comes with the printer will allow you to print up to about 3, 000 pages. These numbers were obtained from printing A4 5% charts, but the actual number of pages will vary depending on the paper type, size, contents, and settings. · The toner cartridge for replacement comes in two types for different number of printable pages: 15, 000 pages and 5, 000 pages. · Toner Cartridges (consumable) are not covered by warranty. However, if there is a problem, contact the dealer where you purchased the printer. · Toner cartridge mouths may become dirty during quality inspection. · To avoid paper jams, make sure paper is not stacked above the limit mark inside the tray. · Do not mix different types of paper in a single paper tray. AQC030S Lift the front of the paper tray (Tray 1), and slowly slide the paper tray back, until it stops. Make sure the tray is fully inserted to prevent paper jams. The power indicator on the control panel lights up. Slowly slide out the paper tray (Tray1), until it stops. Then, lift it slightly, and then pull it out completely. AQC009S · Wait until "Ready" appears on the display panel. · The machine may make a noise while initializing. This noise does not indicate a malfunction. · Do not turn off the power switch until initializing is completed. Doing so results in malfunction. AET045S AET041S Place it on a flat surface. · For details about usable types of paper, see "Loading Paper", Hardware Guide. Next Sheet CLP30DN/CLP27DN/C7531dn/C7526dn/LP231cn/LP226cn/Aficio SP C411DN/Aficio SP C410DN Quick Installation Guide 1/2 Quick Installation Guide 2/2 Test Printing The following explains the procedure for test printing of the configuration page. Test printing in order to verify that the printer is working normally. Test printing checks printer performance only; it does not test the connection to the computer. Quick Instration Guide Network Connection Follow the procedure below to connect the printer to the computer through the network. Prepare the hub and other network devices before connecting the 10 BASET or 100 BASE-TX cable to the machine's Ethernet port. Selecting the Display Language Select a language using the procedure described here. The message for the selected language will appear on the display. [. . . ] } · To install printer driver under Windows 2000/XP Professional, Windows Server 2003, and Windows NT 4. 0, you must have an account that has Manage Printers permission. · Only the printer driver, and not the SmartDevice Monitor for Client is installed when using this printer under USB or parallel. If you connect using USB, see Software Guide. Quit all applications currently running. Select [Effective Protocol] using {} or } {}, and then press the {OK} key. [. . . ]