Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual RICOH CL3000. We hope that this RICOH CL3000 user guide will be useful to you.
Lastmanuals help download the user guide RICOH CL3000.
Detailed instructions for use are in the User's Guide.
[. . . ] Operating Instructions
Maintenance Guide
Getting Started Paper and Other Media Replacing Consumables and Maintenance Kit Cleaning and Adjusting the Printer Troubleshooting Appendix
For safety, please read this manual carefully before you use this product and keep it handy for future reference.
Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read "Safety Information" in this manual before using this machine. [. . . ] · When touching the fusing unit, do not touch any areas other than the handle as it may cause a burn. Replace the fusing unit when the following message appears on the panel display.
ZHBH200E
Transfer Roller
ZHBH590E
Replace Fusing Unit Soon
or
Important Be sure to make the setting from the control panel after replacing the fusing unit. Without it, the procedure is incomplete.
A Turn off the power.
Replace Fusing Unit
Important To prevent a burn, after the power is turned off, be sure to wait about 30 minutes until the fusing unit cools down before touching the fusing unit.
Check the contents of the box for the following items:
38
Fusing Unit Type 125
B Open the front cover by pushing
the front cover release button.
E Remove the fusing unit slowly.
ZHBH230E ZHBP281E
3
C Pinch
the connector lever, and then pull out the connector.
F Take
out the new fusing unit from the box. insert the new fusing unit slowly.
G Place the unit as shown, and then
ZHBH210E
D Push the green release buttons on
ZHBH240E
the left and right outwards to unlock the fusing unit.
H Insert
the fusing unit until it clicks, and then check that the unit is locked.
ZHBH220E
ZHBH250E
39
Replacing Consumables and Maintenance Kit
I Push in the connector.
L Hold the green part as shown, and
then insert the transfer roller into the printer.
3
ZHBH260E
J Turn the green part in the direc-
ZHBH620E
tion of the arrow, and then remove the transfer roller.
Important The end with a longer shaft must be on the left.
M Close the front cover slowly. O Make the setting from the control
panel.
ZHBH600E
K Take out the new transfer roller.
Important Do not touch the roller part.
When "Replace Fusing Unit" Appears on the Panel Display
A If the following message is on the control panel, press the {Escape} key for more than five } seconds. The message disappears and a maintenance reset is performed automatically.
Replace Fusing Unit
When "Replace Fusing Unit Soon" Appears on the Panel Display
A Press the {Menu} key. } "Menu" appears on the panel display.
ZHBH610E
40
Fusing Unit Type 125
B Press the {U} or {T} key to display "Maintenance", and then press the {Enter #} key. }
Menu: Maintenance
C Press the {U} or {T} key to display "Maint. Reset", and then press the {Enter #} key. Reset
D Press the {U} or {T} key to display "Fusing Unit", and then press the {Enter #} key. Reset Fusing Unit
The following message appears.
Fusing Unit: Press # to Reset
E Press the {Enter #} key. } "Ready" appears on the panel display.
41
Replacing Consumables and Maintenance Kit
Intermediate Transfer Unit Type 125
R CAUTION: · The inside of the machine becomes very hot. Do not touch the parts with a "v" label (means hot surface). Touching a part with a "v" label (means hot surface) could result in a burn.
A Turn off the power. B Open the right cover of the printer.
3
Replace the transfer belt when the following message appears on the panel display.
Replace Transfer Belt soon
or
ZHBH290E
C Remove the Waste Toner Bottle.
Replace Transfer Belt
Reference See p. 32 "Waste Toner Bottle Type 125".
Check the contents of the box for the following items:
D Pull out the green levers on the
Transfer Belt
left and right that are fastening the inner cover to unlock the levers.
ZHBH510E
Important Be sure to make the setting from the control panel after replacing the transfer belt. Without it, the procedure is incomplete.
ZHBH300E
42
Intermediate Transfer Unit Type 125
E Lift the inner cover until it stays
up.
G Remove
slowly.
the waste toner bottle
3
ZHBH310E ZHBH650E
F Unlock the waste toner bottle.
H Turn the green screws on the left
and right in the direction of the arrows to loosen them.
ZHBH630E
Important Do not lock the waste toner bottle that has been removed. Toner may spill.
ZHBH520E
The screws are not removed.
I Pinch the both screws and remove
the transfer belt slowly until it stops.
ZHBH640E
ZHBH530E
43
Replacing Consumables and Maintenance Kit
J Raise
the green cover, hold the transfer belt as shown, and then remove the transfer belt.
M Close the green cover, and then
insert it until it stops.
3
ZHBH920E ZHBH540E
Important Be sure to hold the unit with both hands, and then pull it out slowly.
N Turn the green screws on the left
and right in the direction of the arrows to tighten them.
Do not touch the belt part.
K Take out the new transfer belt. L Holding the transfer belt as
shown, insert the transfer belt in the printer.
ZHBH580E
O Place the waste toner bottle in the
position as shown in the illustration.
ZHBH560E
ZHBH660E
44
Intermediate Transfer Unit Type 125
P Lock the waste toner bottle.
S Close the right cover.
ZHBH670E
ZHBH430E
3
Important Be sure to lock the waste toner bottle to prevent toner from leaking inside the printer.
T Turn on the power. U Make the setting from the control
panel.
Q Lower the inner cover slowly.
When "Replace Transfer Belt" Appears on the Panel Display
A If the following message is on the control panel, press the {Escape} key for more than five } seconds. The message disappears and a maintenance reset is performed automatically.
ZHBH410E
R Push the green levers to fasten the
inner cover.
When "Replace Transfer Belt Soon" Appears on the Panel Display
A Press the {Menu} key. } "Menu" appears on the panel display. B Press the {U} or {T} key to display "Maintenance", and then press the {Enter #} key. [. . . ] Important Be sure to disconnect all cables from the printer before transporting it. The printer is a precision piece of machinery. Take care to avoid damage during shipment. If the optional Paper Feed Unit is installed, remove it from the printer, and then move them separately.
75
Appendix
Moving the Printer
R CAUTION: · When lifting the machine, use the inset grips on both sides. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE RICOH CL3000
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual RICOH CL3000 will begin.