User manual RICOH MP6200A

[. . . ] NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installlation. [. . . ] Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. Provides output to a sound card (analog signal). Enhanced IDE (EIDE/ATAPI) Setup Before installation, set the jumper on the jumper connector on the rear panel. The drive can be connected as the Master or Slave on an EIDE (ATAPI) interface. When several (up to four) EIDE devices are connected, each must be set in a unique way. Specific knowledge of hardware and software is necessary to install the drive. We cannot guaranty against direct or indirect damage resulting from improper connections. Ask your supplier for details of the installation procedure. If two peripheral devices with the same settings are both connected to the Primary or to the Secondary EIDE bus, the host computer may fail to run, or may malfunction, so careful attention is necessary. The MP 6200AR Series CS: Cable Select (CSEL) SL: Slave MA: Master Make sure that the host computer is turned OFF when connecting or removing a jumper. Connect the jumper in the vertical direction as shown in Figure 1. If connected horizontally as shown in Figure 2, the drive may malfunction or be damaged. Figure 1. (Master setting) Figure 2. 7 Only one jumper should be installed on the jumper connector. If more than one jumper is installed, the drive may malfunction or be damaged. Master/Slave setting is determined by jumper installation on the Jumper Connector. The following table shows the possible jumper settings. Name MA (Master) SL (Slave) CS Drive mode set by CSEL Drive set as Slave Function Drive set as Master (factory default) The MP 6200AR Series (Cable Select) on the host IDE interface A hard disk is normally installed as the Primary Master on the EIDE (ATAPI) interface. Other EIDE peripheral devices such as hard drives and CD-ROMs are then set differently. 8 4. 1 PC Connections The MP 6200AR Series The CD-RW drive connects to the motherboard of the host computer using an IDE interface cable. Both Primary and Secondary connectors are usually provided on the motherboard, which may be connected as follows: Master Master Slave Slave Primary Secondary Motherboard 9 To Install as a Master Drive To install the drive as a Master, the jumper can be left as supplied from the factory. The MP 6200AR Series Master drive (Booting hard disk) Master drive (CD-RW drive) Primary connector Secondary connector Master drive (Booting hard disk) Master drive (CD-RW drive) Slave drive (Other IDE drive) Primary connector Secondary connector 10 Master drive (Booting hard disk) Master drive (CD-RW drive) Slave drive (Other IDE drive) Primary connector Secondary connector 11 The MP 6200AR Series To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel. The MP 6200AR Series Master drive (Booting hard disk) Slave drive (CD-RW drive) Primary connector Secondary connector Master drive (Booting hard disk) Master drive Master drive (Other IDE drive) 12 Master drive (Booting hard disk) Master drive (Other IDE drive) Primary connector Slave drive (CD-RW drive) Secondary connector 13 The MP 6200AR Series 5. How to Use the Discs When using CD-ROM discs, CD-R discs or CD-RW discs, don't attach any stickers or labels to the discs. [. . . ] · Use compressed air to clear dust from the drive. (Spray the compressed air for about 5 seconds). 1) · Check to see if there is dirt on the surface of the disc. Be careful not to touch the disc with the fingers when doing this. [. . . ]