User manual RICOH MP7240A

[. . . ] To view this manual, use following browsers Microsoft Internet Explorer 4 or later Netscape Communicator 4 or later NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installlation. [. . . ] UDMA Capable q q q *1 *2 Bundled software does not support this writing format. The speed at which to write on the current standard CD-RW disks is 4x recording (at a data transfer rate of 600KB/second). Explains the system environment required for using the drive as a CD-R/CD-RW drive. IBM PC/AT compatible PC Operating System Windows ME/98/95(ORS2 or later) Windows NT Workstation Ver. 4. 0 (Service Pack 4) or later Windows 2000 (Professional) and XP Pentium 200 MHz or higher (when using Just Link) 64MB or more Hard disk with average access time of 19msec or less, and data transfer speed of 1, 200KB/sec or greater. Enhanced-IDE interface (as Primary Slave, Secondary Master, or Slave) 5. 25-inch half height bay required +5V/+12V power socket required CD-R: CD-RW: High Speed CD-RW: Ricoh, Mitsubishi Chemical, Taiyo Yuden, Mitsui Chemicals, TDK and Maxell discs Ricoh and Mitsubishi Chemical discs Ricoh and Mitsubishi Chemical discs CPU Memory Harddisk Interface Drive bay Power Recommended discs Multi-read compatible (Random UDF compatible) drives are: q q Drives that can read low reflectivity discs. Drives that support Packet Writing. Front Panel Rear panel Front Panel 1. Disc tray This is the tray for the disc. Place the disc on the ejected disc tray, then lightly push the tray (or push the eject button) and the disc will be mounted. Caution Don't use force to pull out or push in the disc tray. This might cause damage to the loading section of the drive. 2. Headphone jack This jack is for connecting headphones or mini-speakers. 3. Volume control This is used to adjust the output volume of the headphone jack. It can't be used to adjust the output volume for the audio output connectors on the rear panel. Caution Turn the volume down before turning on the power. Sudden loud noises can damage your hearing. 4. Busy indicator This indicator lights orange when a disc is mounted into the drive. When the disc is being accessed, it flashes or lights orange. If a disc is not mounted, the indicator does not light even when the power is turned on. When a illegal disc is loaded or some hardware trouble occurs, the indicator blinks. 5. Eject button This is the button used to eject or insert in the disc tray. 6. Emergency eject hole This drive has a function that allows the disc to be ejected manually if this becomes necessary in an emergency such as failure of the drive or a power outage. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Rear panel 1. Digital Audio Output Connector Provides output to a sound card (Digital signal). 2. Analog Audio Output Connector Provides output to a sound card (Analog signal). 3. Jumper Connector This jumper determines whether the drive is configured as a master or slave. Changing the master-slave configuration takes effect after power-on reset. 4. IDE Interface Connector Connect to the IDE (Integrated Device Electronics) interface using a 40-pin flat IDE cable. Caution Do not connect or disconnect the cable while the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Caution Be careful to connect it the proper way. Connecting the wrong way may damage the system (and is not covered under the warranty). Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. [. . . ] Master drive (the drive) Master drive (Booting hard disk) Secondary connector Primary connector Slave drive (Other IDE drive) To Install as a Slave Drive To install the drive as a Slave, change the jumper setting on the rear panel. Master drive (Booting hard disk) Slave drive (the drive) Secondary connector Primary connector Master drive (Other IDE drive) Back Next 1. Sound Card Connection If the computer has a sound card, the drive can be connected to the sound card with an audio cable. Make sure the connections are oriented so that L corresponds to L and R to R. [. . . ]