User manual RICOH MP9060A

[. . . ] Conventions Contents Conventions Introduction Introduction Handling Procedures Features Handling Procedures Features System environment System environment Drive functions and settings Drive functions and settings Installing the Drive Installing the Drive How to Use the Drive Specifications How to Use the Drive Specifications NOTICE This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communication. However, there is no guarantee that interference will not occur in a particular installlation. [. . . ] (Mode1, Mode2, Form1)[Read only] 1, 362 KB/sec. (Mode2, From2) Internal type (bare drive) Enhanced-IDE (ATAPI) 2MB 16. 6MB/sec. (Max. ) DVD-ROM Read speed Average access time Initial processing time 4X: 5. 5 MB/sec. or less horizontal/vertical Format CD-DA CD-ROM CD-Extra CD-ROM XA Photo CD*3 CD-i*3 CD-ROM + CD-DA Video-CD CD-Text Write Read Play*2 Mounting direction Compatible formats * * * * * * * * * * * * * * * * * * * * * * * Loading system Power Power consumption Tray type (automatic loading/eject) DC5V, DC12V 12w max. (standby) Weight Dimensions Reliability Less than 1. 5 Kg. 148. 4 X 198(included front panel) X 42. 5mm Error Rate: MTBF: MTTR: Temperature Humidity Vibration Shock Environmental dust 10-12 bits or less 100, 000hours or greater Within 30 minutes When operating When not operating 5°C to 40°C (No air cooling) -30°C to 65°C 55% to 90% R. H. (No condensation) (No condensation) 0. 035mmpp(10 to 45Hz) 1 X 9. 8 m/s2 0. 025mmpp(45 to 65Hz) (5 to 300Hz) 0. 2 X 9. 8 m/s2 (65 to 150Hz) 2 2 X 9. 8 m/s 40 X 9. 8 m/s2 (11msec. half sine) Class 3 million or less (3 million particles of 0. 5 micron dustper cubic foot or less) Environmental Conditions *1 Speed is automatically reduced if reading is unsuccessful. Also, "Read" means transferring data. *3 CD-i and Photo-CD discs require special reader/player. Also, Photo-CD requires a license from Kodak. The drive's appearance and specifications may change without notice. Disc CD-R Characteristic External diameter Dimensions Internal diameter Thickness Recording area (User area) Time Recording capacity Track pitch Substrate material Recording material Reflectance (R to p) Eccentricity Maximum camber angle Recommended recording power Playback power Playback stability Environment for use Storage life Capacity Linear speed 80min. *1 700MB 1. 2m/s CD-R ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. 650MB 1. 2m/s 1. 6 ± 0. 1µm Polycarbonate Organic pigment (phthalocya-nine) / Au or Ag lamination (Organic protective layer attached) 65% or more 70µm or less 0. 4° or less 6 to 7mW(at É:785nm, NA:0. 5) 1mW or less 106times or more (Playback power = 0. 7mW) -5 to 55°C 5 to 95%RH 100 years or more 5 to 25°C, 5 to 60%RH Avoiding direct sunlight) 63min. 550MB 1. 4m/s CD-RW CD-RW ø120mm ø15mm 1. 2mm ø50 to 116mm 74min. Caution Do not connect or disconnect the cable when the power is on, as this could cause a short circuit and damage the system. Always turn the power OFF when connecting or disconnecting the cable. 5. Power Connector Connects to the power supply (5 and 12V DC) of the host computer. Caution Be careful to connect with the proper way. Connecting the wrong way may damage the system (and is not guaranteed). << Contents Emergency Eject This drive has a function that allows the CD to be ejected manually, if this becomes necessary in an emergency such as failure of the drive or a power outage. Follow the following procedures in such a case. Caution This feature is a last measure to be used only in an emergency. Using it excessively will cause malfunction. Insert a fine tipped object into the emergency eject hole. The front door pops open and the disk tray comes partway out. [. . . ] before securing the drive. Back Next 1. Connecting the Power Connector Connect the power cable from the computer's power supply to the socket on the drive unit, fitting the connector properly into the socket. If there is no spare power cable available in the computer, you will have to purchase a splitter cable of a suitable type. Back Next 1. Device Drivers << Contents 5. [. . . ]