User manual RIDGID TS24241

[. . . ] 76 2:1(5·6 0$18$/ , 1&+ &2175$&725 6(5, (6 %(/7 '5, 9( 6$: )RU <RXU 6DIHW\ Part No. SP6250 5HDG DOO LQVWUXFWLRQV FDUHIXOO\ Printed in U. S. A. Table of Contents Section Page Table of Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 2 Safety Instructions For Table Saw . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 3 Safety Signal Words . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Open owners manual so that 8 pages are separated from the rest of the book. Use these pages like a feeler gage to set the spacing between the bottom of the fence and the table top. Rip fence should clear saw table/extension surface just enough to allow pages to slide back and forth under rip fence. If rip fence is too high or too low, loosen nuts holding front guide bar and adjust bar up or down. Wrench tighten nuts when proper alignment is achieved. Slide fence left and right on guide bar to ensure clearance from side to side and from front to back. If necessary readjust rip fence guide bars to get proper clearance. Wrench tighten all nuts holding guide bars in place. NOTE: During this adjustment, the left/right positioning of the guide bars could be affected. Realignment may be necessary. Owners Manual 8 Pages 27 Assembly (continued) Rip Fence Alignment Adjustment WARNING: A misaligned fence can cause kickbacks and jams. To reduce the risk of injury, follow these instructions until the fence is properly aligned. The rip fence must be PARALLEL with the sawblade and miter gauge grooves. Clean any debris off the fence guide bars. Move fence until it is along side the miter gauge groove and lock it. Using a 5/32" hex "L" wrench, loosen the four button head screws located to each side of the rip fence handle. Hold fence head tightly against front guide bar. Align fence channel so that it is parallel with groove. Carefully lock the fence in this position. Repeat steps as needed until fence channel is aligned with miter gauge groove. Miter Gage Groove Button Head Screws for Adjusting Fence Parallelism Rip Fence Lock Lever Adjustment WARNING: Make sure the fence lock works in the center and at each end of the fence guide bar. An improperly adjusted fence could move. Movement could cause binding or kickback. The rip fence lock lever when locked down should hold the rip fence securely. [. . . ] Complete Nut Push Pin 1/4 x 1-1/2 Support, Guard Guard, Saw Pin, 1/4 x 1-3/4 * Washer, 17/64 x 5/8 x 1/16 Spacer, Pawl Pawl Spreader Blade Pin, 1/4 x 1 * Pin, Roll 3/16 x 15/16 Spring, Pawl Bag Asm, Guard * Standard Hardware Item - May be purchased locally ­ Items Not Shown 64 Repair Parts Parts List for RIDGID 10 Inch Table Saw Model No. TS24241 RIDGID parts are available on-line at www. ridgidparts. com Figure 7 - Leg Set 3 2 1 11 15 16 5 17 2 2 9 8 14 10 14 4 15 2 6 7 3 8 7 6 9 12 1 12 13 Key No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 16 17 ­ Part No. Description 805589-5 Screw, Serrated Truss Head. 1/4-20 x 1/2 826113-1 Leg 826116 Stringer, Side 826115 Stringer, End 509511 Stringer, End w/Label 115120 * Nut Hex, 1/4-20 114604 * Lockwasher 1/4 826114-1 Brace Leg (Short) 826114 Brace Leg (Long) 824832 Hanger, Miter Gauge 824833 Hanger, Rip Fence 118645 * Nut Hex 3/8-16 803835-3 Foot Leveling Hardware for Attaching Legs to Saw 60038 * Screw, Hex Hd. [. . . ]