User manual RME MADIWIN

[. . . ] User's Guide Hammerfall® DSP System MADI TotalMix 24 Bit / 192 kHz ü SyncAlign ® TM ZLM ® SyncCheck TM ® SteadyClock PCI Busmaster Digital I/O Card 64 Channels MADI Interface 24 Bit / 192 kHz Digital Audio Stereo Analog Monitoring 64 x 64 Matrix Router 2 x MIDI I/O MIDI embedded in MADI Quick Boot Contents Introduction. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Package Contents . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 System Requirements. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 4 Brief Description and Characteristics. . . . . . . . . . . . . . . . . . . [. . . ] This causes a lot of confusion, as the driver seems to behave completely buggy, and the user does not recognize the simple reason for it ­ for example simultaneous operation of ASIO and GSIF on the same channels. In case Gigastudio loads well, load gig files too, but won't play at all even when using the virtual keyboard: Go to Hardware/Routing and select a valid MIDI input port. Note that blank is not valid, but <none> is. *The limitation of 32 channels is caused by Gigastudio 2. 54. According to Tascam, Gigastudio 3 will support 64 channels. User's Guide Hammerfall DSP MADI © RME 23 15. TotalMix: Routing and Monitoring The Hammerfall DSP system includes a powerful digital real-time mixer. RME's unique TotalMix technology allows for nearly unlimited mixing and routing with all inputs and playback channels simultaneously. Here are some typical applications for TotalMix: · · · · · · setting up delay-free submixes (headphone mixes) unlimited routing of inputs and outputs (free utilisation, patchbay function) distributing signals to several outputs at a time simultaneous playback of different programs over only one stereo channel mixing of the input signal to the playback signal (complete ASIO Direct Monitoring) integration of external devices (effects etc). in real-time The block diagram of the TotalMix mixer of the HDSP MADI shows that the record signal always stays un-altered, but can be passed on as often as desired, even with different levels. The level meter of inputs and playback channels are connected pre-fader (due to the enormous routing capabilities). The level meters of the hardware's outputs are connected post-fader. User's Guide Hammerfall DSP MADI © RME 24 15. 1 Elements of the Surface The visible design of the TotalMix mixer is mainly determined by the architecture of the HDSP system: Upper row: hardware inputs. The level shown is that of the input signal, i. Per fader and routing window, any input channel can be routed and mixed to any hardware output (third row). · Middle row: playback channels (playback tracks of the software). Per fader and routing window, any playback channel can be routed and mixed to any hardware output (third row). Because they refer to the output of a subgroup, the level can only be attenuated here (in order to avoid overloads), routing is not possible. This row has two additional channels, the analog outputs. Every single channel has various elements: Input and playback channels each have a mute and solo button. Below each there is the panpot, realized as indicator bar (L/R) in order to save space. In the window below this, the present level is displayed in RMS or Peak, being updated about every half a second. Overs are indicated here by an additional red dot. The meter shows both peak values (zero attack, 1 sample is enough for displaying full scale) by means of a yellow line and mathematically correct RMS values by means of a green bar. The RMS display has a relatively slow time constant, so that it shows the average loudness quite well. [. . . ] If you suspect that your card is faulty, please contact your local retailer. The warranty does not cover damage caused by improper installation or maltreatment - replacement or repair in such cases can only be carried out at the owner's expense. RME does not accept claims for damages of any kind, especially consequential damage. Liability is limited to the value of the Hammerfall DSP. [. . . ]