User manual ROBLIN ACTIS ELECTRO 5741

[. . . ] If the room where the hood is to be used contains a fuel-burning appliance such as a central heating boiler then its flue must be of the room sealed or balanced flue type. If other types of flue or appliances are fitted ensure that there is an adequate supply of fresh air to the room. Ensure the kitchen is fitted with an airbrick, which should have a cross-sectional measurement equivalent to the diameter of the ducting being fitted, if not larger. The ducting system for this cooker hood must not be connected to any existing ventilation system, which is being used for any other purposes or to a mechanically controlled ventilation ducting. [. . . ] Press the `+' button (while the motor and lights are switched `OFF') until the five LED lights will flash once to indicate confirmation that the cooker hood is in the extraction mode. B - BASIC INSTRUCTIONS Lighting Press LED button 1 to switch `ON' the lights and the LED will illuminate to confirm the lights are switched `ON'. Motor Press LED button 2 to switch `ON' the fan motor (and adjust the speed of the fan motor by pressing the LED button `+' and `-`) and the LED lights 2, 3 and 4 will illuminate. The fan speed will be increased if constant pressure is kept on the (+) button. LED 2 : Minimum speed - cooking with one pan or simmering LED 2 & 3 : Medium speed - normal cooking with up to 4 pans LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm fan is switched `ON'. c - COMPLEMENTARY INSTRUCTIONS · Boost speed : To obtain the best performance it is advisable to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking. to program the complementary function , proceed as follows: - Press LED button 2 to switch `ON' the fan motor and adjust the speed of the fan by pressing the LED button `+' and `-`. You should keep applying pressure to the `+' and `-` button until the required speed is selected. It is advisable too that you should leave it running in the boost setting for approximately 5 minutes after finishing. Pre-set stop of the boost speed : A pre-set stop after 5 minutes of the boost speed is available. Your cooker hood is supplied with a deactivated pre-set stop of the boost speed. To use the cooker hood with a pre-set stop of the boost speed re-programme the hood as follows: The lights and the fan motor should be switched `OFF' to set the timer. Push the LED button `-' until the LED lights will flash : One flash of the LED lights 2, 3, and 4 = function is switched `OFF'. Two flashes of the LED lights 2, 3, and 4 = function is switched `ON'. While the 5 minutes timer is running, It is available to stop immediately the boost speed by pressing the led button 5. While the 5 minutes timer is running, the indication of saturation of the filters is switched `OFF'. If a pre-set stop for the hood is switched `ON' and the 5 minutes timer is still running, the boost speed will be switched `OFF' together with the pre-set stop for the hood after the count down of 5, 10 or 15 minutes. It is available to stop the boost speed before the count down of the preset stop of the hood by pressing the led button 5. Pre-set stop for the hood : This function allows you to program the cooker hood to automatically stop cooking after a pre-set period. The lights and the fan motor should be switched `OFF' to set the timer. Indication of saturation of the metal grease filters : After 200 hours use, one quick flash of the LED 1 will indicate that you must clean the metal grease filters. To reset the 200 hours timer back to zero requires the motor and lights must be switched `OFF'; then and proceed as follows: Press the LED button `+' for 3 to 4 seconds and the LED lights 1, 2, 3, 4 and 5 will flash to confirm the programme has been reset to zero. [. . . ] If lamp failure has occurred then it should be replaced with identical replacement. Do not replace with any other type of lamp and do not fit a lamp with a higher rating. In the event of any malfunction or anomaly, notify your fitter who will have to check the appliance and its connection. In the event of damage to the mains supply cable, this can only be replaced by at approved repair centre appointed by the manufacturer who will have the required tools and equipment to carry out any repairs properly. [. . . ]