User manual ROBLIN ATRIUM 1200 DIMENSIONS

[. . . ] This cooker hood is fitted with a 3-core mains cable with a standard 10/16A earthed plug. ⷠAlternatively the hood can be connected to the mains supply via a double-pole switch having 3mm minimum contact gap on each pole. ⷠBefore connecting to the mains supply ensure that the mains voltage corresponds to the voltage on the rating plate inside the cooker hood. To ensure the safe operation of this cooker hood, we recommend that the hood should not be fitted below 65cm (for electric) or (70cm for gas) the measurements taken from the surface of the cooking appliance to the underside of the cooker hood. [. . . ] Splashback (optional): When a splashback is to be fitted, the distance between the hood and the cooking appliances will be determined by the height of the splashback item B and whether or not there is a raised back on the worktop. the splashback is to be installed before installing the canopy. If the splashback is to be fixed to the wall using both the top and bottom fixing holes, Care must be taken to ensure that the splashback is fitted at the correct height before fixing the base units or at least the worktop covering them. As this is a complex operation, it should only be undertaken by the technician installing the kitchen units or by a competent person who knows the final dimensions of the units. 4) Fixing the canopy: Before starting to fix the canopy it will be necessary to adjust the support brackets by turning the adjustment screws Vr in a clockwise direction until their reach their limit (Fig. Level the hood by turning the adjustment screws and then locking the screws 1. 5) Ducting: The hood is more effective when used in the extraction mode (ducted to the outside). When the cooker hood is ducted to the outside, charcoal filters are not required. The ducting used must be 150 mm (6 INS), rigid circular pipe and must be manufactured from fire retardant material, produced to BS. Wherever possible use rigid circular pipe which has a smooth interior, rather than the expanding concertina type ducting. The above assumes our 150 mm (6 INS) ducting is being installed. The fan speed will be increased if constant pressure is kept on the (+) button. LED 2 : Minimum speed - cooking with one pan or simmering LED 2 & 3 : Medium speed - normal cooking with up to 4 pans LED 2, 3 & 4 : Maximum speed - frying and cooking foods with strong odours Press LED button 5 to obtain the boost position for maximum effect and the LED will illuminate to confirm fan is switched `ON'. c - COMPLEMENTARY INSTRUCTIONS · Boost speed : To obtain the best performance it is advisable to switch `ON' the cooker hood a few minutes (in the boost setting) before you start cooking. to program the complementary function , proceed as follows: - Press LED button 2 to switch `ON' the fan motor and adjust the speed of the fan by pressing the LED button `+' and `-`. You should keep applying pressure to the `+' and `-` button until the required speed is selected. It is advisable too that you should leave it running in the boost setting for approximately 5 minutes after finishing. ⷠPre-set stop of the boost speed : A pre-set stop after 5 minutes of the boost speed is available. Your cooker hood is supplied with a deactivated pre-set stop of the boost speed. With a pre-set stop of the boost speed re-programme the hood as follows: The lights and the fan motor should be switched `OFF' to set the timer. Push the LED button `-' until the LED lights will flash : One flash of the LED lights 2, 3, and 4 = function is switched `OFF'. Two flashes of the LED lights 2, 3, and 4 = function is switched `ON'. [. . . ] 5 - While the LED is flashing select the motor type used while pushing one of the 5 buttons in accordance with the following: BUTTON 0/1 Light : Motor EBM PRO 220-240 V AC 50 Hz / 220 V AC 60 Hz. lighting : If the lamp fails to function check to ensure it is fitted correctly into the holder. If lamp failure has occurred then it should be replaced with identical replacement. Do not replace with any other type of lamp and do not fit a lamp with a higher rating. [. . . ]