User manual ROCKTRON REPLITONEMP

[. . . ] Digital Modeling Preamp MANUAL o o o o o o 16 Amplifier Emulations Direct Recording Capabilities 128 User Programable Presets Available HUSH ® Noise Reduction Rocktron's Hallmark Effects Reverb, Delay, HUSH, & one additional effect available at all times! Suggested Footcontroller(s) - Rocktron MIDI Mate, Rocktron MIDI I. T. ® Suggested MIDI Cable(s) - Rocktron M7 Pin MIDI Cable Model # RMM900 Suggested Power Amplifier(s) - Rocktron Velocity 100 (2x50 Watt) Suggested Speaker Cabinets(s) - Rocktron Velocity S112 (1x12 cabs) ® May be covered by one or more of the following: U. S. Patents #4538297, 4647876, 4696044, 4745309, 4881047, 4893099, 5124657, 5263091, 5268527, 5319713, 5333201, 5402498 and 5493617. Foreign patents pending. 1 Your Rocktron RepliTone MP TM preamp has been tested and complies with the following Standards and Directives as set forth by the European Union: Standard(s): IEC60065 Professional Audio/Video or Similar Equipment, EN55013:1997, EN61000-3-2 (1995) EN61000-3-3(1995), EN55020:1995, CSA E65-94 This means that this product has been designed to meet stringent guidelines on how much RF energy it can emit, and that it should be immune from other sources of interference when properly used. [. . . ] This feature allows you to use a stereo Y cable (not included) to run into a PA system (eliminating the need to haul the power amp and speaker cabinets to the gig) or allow you to record direct into a mixing board or home studio. If you do not have a stereo Y cable you can activate the speaker simulator out of the Left & Right Pre-amp outputs by plugging in a 1/4" guitar cable or 1/4" stereo dummy jack into this headphone/direct/recording output jack and then use two standard 1/4" guitar cables from the Pre-amp outputs into the PA or recording device. 5 LOOP SEND and RETURN jacks The effects loop is provided to allow for a chain of external stereo (L/R) effects devices to be inserted into the signal path after the preamp and built-in effects and before the power amp. NOTE: To maintain stereo operation, the effects loop must be used in a stereo configuration. This requires only stereo RTS connections to be made to the send and return jacks. Using mono TS (tip-sleeve) connections will mute the right channel. 6 POWER jack and ADAPTER Provides AC power to the Replitone MP - please use the enclosed 9VAC 3. 4 amp adapter for this product only. Do not use any adapter other than the included adapter. Rocktron is not responsible for improper use. Please follow all precaution instuctions included in the front of this manual. Here are the model numbers: Model Number 006-1211 - this is a 110V 9VAC 3. 4A Adapter 4 Pin/Din for RepliTone MP Model Number 006-1224 - this is a 220V 9VAC 3. 4A adapter 4 Pin/Din for RepliTone MP Please check our website for more details www. rocktron. com 11 11 8. MIDI Implementation There are 128 user programmable presets. The first 15 are accessible from the front panel PRESET knob and correspond to MIDI program change numbers 1 to 15. ("Manual" is not a MIDI accessible preset. ) The remaining 113 user presets are accessible only via MIDI program changes (program numbers 16 to 128) through a footcontroller. The MIDI IN jack is a 7-pin DIN for phantom powering MIDI controllers, however, 5-pin DIN cables can be used and are most common. The MIDI channel will be permanently set to OMNI, you can plug in any MIDI pedal and it will work. However for the best function we recommend the Rocktron MIDI Mate or MIDI I. T. and the RMM900 7pin MIDI Cable. Storing Presets o Storing Presets to Exisiting Location: Once you have achieved a sound that you like, you may want to save it for later use. If any parameter has been modified, the STORE LED will light. The STORE (EXECUTE) LED will start flashing. If you would like to store the changed sound at the current or exisiting preset - press the store button again to execute the change or complete the store. o Storing Presets to a different location: If you would like to save the changed sound to a different preset - press the STORE (EXECUTE) button. The STORE (EXECUTE) LED will start flashing. Now turn the preset knob to the number where you want to save or choose the location number on your MIDI Footcontroller. You will now hear the sound of the preset location which you selected when turning the knob. [. . . ] It simulates the natural acoustics of playing in a large hall or auditorium. This is also known as "ambience". Reverb is useful for creating a "surf guitar" sound or for adding sustain to clean guitars. Just a touch of reverb will embellish your sound without being discernable as an effect. [. . . ]