User manual ROLAND AR-100

[. . . ] No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. For the U. K. IMPORTANT: THE WIRES IN THIS MAINS LEAD ARE COLOURED IN ACCORDANCE WITH THE FOLLOWING CODE. BLUE: NEUTRAL BROWN: LIVE As the colours of the wires in the mains lead of this apparatus may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: The wire which is coloured BLUE must be connected to the terminal which is marked with the letter N or coloured BLACK. The wire which is coloured BROWN must be connected to the terminal which is marked with the letter L or coloured RED. [. . . ] Phrase 1 0001 2 0002 3 0003 4 0004 5 0005 9 0009 Operational Specifications for Direct Playback (Last-In) Basic Operation of Direct Playback (Reverse Priority) fig. inp-10 Playing Back Phrases Assigned to the Connectors (Direct Playback) What Is Direct Playback (Reverse Priority)?/Use and Applications By inputting control signals directly to Port Nos. 1 through 9, you can play back the phrases assigned to those numbers. Assign phrases 1 through 9 beforehand to Port Nos. This is very convenient when you want to specify a desired phrase directly using a switch, relay, sensor, or other such means. fig. inp-08 Port No. 2 STOP Port 0002 0001 AUDIO OUTPUT 0001 Interrupted Playback: Input control signals to Port Nos. This plays the phrase assigned to the connector. stopping: Input control signals to Port No. This stops playback of the phrase. A Control Signal A Control Signal A Control Signal A Control Signal A Control Signal A Control Signal 2 3 4 5 Port No. 1 Phrase 0001 0002 0003 0004 0005 9 0009 "Operational Specifications for Control Input Playback" (p. 28) Priority Order The most recently input control signal is given priority in playback. If a new and different control signal is input during playback of a phrase, playback of the current phrase is stopped, and playback of the specified phrase then begins. fig. inp-11 Connecting External Devices Connectors Used for Direct Play (Last-In) (Control I/O Connector) 1 through 9: Inputting a control signal directly to the connector with the number corresponding to the phrase starts playback of the phrase. 11 and 12, and input a control signal to the Port No. Stopping: Input a control signal to Port No. The basic operation of Binary Playback is shown below. fig. inp-17 To Specify Phrases with Binary Signals Example: Specifying Phrase 0112 (Phrase #: 0112) 1. Convert the phrase number to a binary signal number. "0" (Off) "1" (On) Binary Specification Port No. 1--8 0001 0002 0003 Disabled "Phrase Number / Binary Signal chart" (p. 33) The phrase number "0012" becomes the binary signal "01110000. " With the above step, Phrase No. 0112 is converted to: fig. inp-18 START Port 0001 0001 0002 0003 AUDIO OUTPUT Binary specified phrases are played back repeatedly. Playback is repeated while the start signal is continuously input. You can begin playback of phrases by specifying phrases in binary with the start signal continuously being input. When the START connector control signal switches to Off, the current phrase finishes, and then playback is stopped. No action results when a new start signal is input while a phrase is being played back. Port No. [. . . ] (AR-100 Model ID=00H, 38H) Address Block Map An outlined address map of the Exclusive Communication is as follows; Exclusive Address Table Phrase Select Address(H) SIZE(H) DATA(H) Parameter Description =================================================================== 01 00 10 00 00 02 00 - 07 Phrase Number upper 4bits 11#` 00 - 7f Phrase Number lower 7bits =================================================================== Phrase number DATA(H) A0001 - A1000 * * 00 00 - 07 67 Only received packet data. When reception of this packet is completed, the AR-100 changes to the current (currently displayed) phrase number. (AR-100/2000 compatible) Address(H) SIZE(H) DATA(H) Parameter Description =================================================================== 01 00 00 00 00 02 00 - 07 Phrase Number upper 3bits 01# 00 - 7f Phrase Number lower 7bits =================================================================== Phrase number DATA(H) A0001 - A0500 00 00 - 03 73 Appendices * * Only received packet data. When reception of this packet is completed, the AR-100 changes to the current (currently displayed) phrase number. Exclusive Address Table Recording Settings Address(H) SIZE(H) DATA(H) Parameter Description =================================================================== 01 00 10 00 00 03 00 - 07 Phrase Number upper 4bits 11# 00 - 7f Phrase Number lower 7bits 12# 00 - 02 REC Source 0:ANALOG-IN 1:DIGITAL-IN 2:MIDI-IN =================================================================== Phrase number DATA(H) A0001 - A1000 * * 00 00 - 07 67 Only received packet data. When reception of this packet is completed, the AR-3000 goes into REC PAUSE mode. [. . . ]