User manual ROLAND AR-1000

[. . . ] Roland has licensed this technology from the TPL Group. Copyright © 2006 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. * 4 0 6 7 6 4 6 7 - 0 4 * USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers to damage or other adverse effects caused with respect to the home and all its furnishings, as well to domestic animals or pets. The symbol alerts the user to important instructions or warnings. The specific meaning of the symbol is determined by the design contained within the triangle. [. . . ] Such noise could occur when receiving or initiating a call, or while conversing. Should you experience such problems, you should relocate such wireless devices so they are at a greater distance from this unit, or switch them off. When moved from one location to another where the temperature and/or humidity is very different, water droplets (condensation) may form inside the unit. Damage or malfunction may result if you attempt to use the unit in this condition. Therefore, before using the unit, you must allow it to stand for several hours, until the condensation has completely evaporated. 2 352b · · When handling the board, grasp it only by its edges. Avoid touching any of the electronic components or connectors. 3 · When handling the board, grasp it only by the panel or the board's edges. Avoid touching any of the electronic components or connectors. 4 355b · · Before you connect any cables, make sure they do not carry a static electricity charge. Such charges can be transmitted, for example, if the other end of the cable has been in contact with a carpet (or other object) where there is a static electricity buildup. 5 · Save the bag in which the board was originally shipped, and put the board back into it whenever you need to store or transport it. 901(F) Maintenance 401a · · For everyday cleaning wipe the unit with a soft, dry cloth or one that has been slightly dampened with water. To remove stubborn dirt, use a cloth impregnated with a mild, nonabrasive detergent. Afterwards, be sure to wipe the unit thoroughly with a soft, dry cloth. Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/or deformation. Veuillez suivre attentivement les instructions suivantes quand vous manipulez la carte afin d'éviter tout risque d'endommagement des pièces internes par l'électricité statique. · Toujours toucher un objet métallique relié à la terre (comme un tuyau par exemple) avant de manipuler la carte pour vous décharger de l'électricité statique que vous auriez pu accumuler. 1 402 · 2 · Lorsque vous manipulez la carte, la tenir par les côtés. 3. fig. 00 Couper le contact sur l'appareil AR-3000/AR-3000R et débrancher la prise d'alimentation. Retirer du panneau arrière les deux vis de la fente pour la carte d'option et retirer le couvercle. Retirer du panneau supérieur les quatre vis pour la carte d'option et retirer le couvercle. 3 7. Insérer à fond le connecteur de la carte d'option dans le connecteur de l'unité. 3. Use the [SELECT] dial to select "10. 2 Network Address, " then press the dial. Turn the [SELECT] dial to select the setting value, then press the dial. The entry location shown below is highlighted. Turn the [SELECT] dial to select the characters for the password (letters or numbers), then press the dial. fig. 9. 4. Repeat the operation in step 3. Once you've finished supplying values for the settings, press the [ENTER] button. A screen asking you to confirm the write procedure appears. (The confirmation screen appears even if you enter the final item and press the dial. ) To write the settings to the unit, press the [ENTER] button. To cancel, use the [SELECT] dial to choose "NO, " then press the [ENTER] button. You are returned to the Setting Item Selection screen. * The settings for the network address will take effect the next time you power up. Repeat step 7. When you have finished entering the password (5 to 8 characters), press the [ENTER] button. [. . . ] This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: ­ Reorient or relocate the receiving antenna. ­ Increase the separation between the equipment and receiver. [. . . ]