User manual ROLAND AR-200R

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. The manual should be saved and kept on hand as a convenient reference. Copyright © 2006 ROLAND CORPORATION All rights reserved. [. . . ] In addition to the connectors just described, shorting the "11/12 (GND)" (ground) connectors enables "On. " fig. inp-09 Port No. 1 Port NO. 2 0001 0002 AUDIO OUTPUT 0001 Interrupt STOP 10 9 Select a Phrase 1 1 2 COM Playback is repeated while the control signal is continuously input. fig. inp-12 Port No. 1 12 11 COM 0001 AUDIO OUTPUT 0001 0001 * Control Input and DC Input Terminal (CONTROL A) "1, 2" are connected in parallel with Control I/O Connector (Control B) "1, 2. " 30 Controlling the AR-200R from an External Device (Control Input Connectors) AR-200R Settings Selecting the Control Input Mode Set the MODE switches on the AR-200R's bottom panel to select "DIRECT PLAYBACK" from the control input modes (PLAYBACK BY CARD DATA/DIRECT PLAYBACK/ BINARY PLAYBACK/INTERVAL PLAYBACK). You cannot achieve control input playback merely by connecting a device to the port. Be sure to set the control input mode and match the method used for connecting to the connectors. fig. inp-14 Binary Specification Port No. 1--8 87654321 01110000 START SIGNAL Phrase 112 PLAY * To conduct Binary Playback, you will need to obtain a control device capable of generating binary signals. * Input of binary specifications should be completed in no more than 50 milliseconds. Connecting External Devices Connectors Used in Binary Playback "1­8": Phrases are specified in binary format using combinations of 0 (Off) and 1 (On). "9 (START)": Start phrase playback. "10 (STOP)": Stop phrase playback. In addition to the connectors just described, shorting the 11/ 12 (GND) (Ground) connectors enables "On. " fig. inp-15 Procedure for Setting the Control Input Mode 1. Set the MODE switches on the AR-200R's bottom panel as shown below. * Use a pointed object to change the ON/OFF settings of the MODE switches. Applications START Select a Phrase STOP 10 9 8 1 Assigning Phrases to the Terminals Assign phrases 1 through 9 to Port Nos. 1 through 9. Settings in Effect When a Card Is Formatted fig. inp-13 12 11 Port No. Phrase 1 0001 2 0002 3 0003 4 0004 5 0005 9 0009 GND Specifying Phrases in Binary Notation (Binary Playback) What Is Binary Playback?/Use and Applications By inputting binary (Base 2) signals to Port Nos. 1 through 8 to select a phrase and inputting a start message to the START terminal, you can then play back the selected phrase. A maximum of 250 phrases can be selected and played back with this method. This allows you to specify 250 phrases with control signals (from a switch or other ON/OFF signal device), without having to use computers or other complicated equipment. "Important Notes on Making Connections and Switching the Power On and Off" (p. 9) Even without connecting to all eight connectors used for making the binary specifications, you can still conduct Binary Playback. The number of phrases that can be specified is determined by the formula "two to the nth power minus one" (with "n" being the number of connectors used). Example: Using three timers or other such devices capable of outputting the necessary signals gives two to the third power minus one (i. e. , 8 - 1 = 7), meaning you can specify the seven phrases 001 through 007. However, start signals feature other special requirements. 31 Controlling the AR-200R from an External Device (Control Input Connectors) Operational Specifications of Binary Playback Basic Operation of Binary Playback fig. inp-16 Procedure for Setting the Control Input Mode 1. Set the MODE switches on the AR-200R's bottom panel as shown below. Turn on the power of the AR-200R. Binary Specification Port No. 1--8 0001 START Port 0001 AUDIO OUTPUT * Use a pointed object to change the ON/OFF settings of the MODE switches. Playback: Specify the phrases using combinations of 0 (Off) and 1 (On) signals to Port Nos. 11 and 12, and input a control signal to the Port No. [. . . ] However, if a phrase has already been saved, the AR-3000 deletes that phrase and goes into REC PAUSE mode. 63 MIDI Implementation Chart AUDIO RECORDER Model AR-200R Date : July. 1, 2006 MIDI Implementation Chart Transmitted Recognized Version : 1. 00 Remarks Media Player Section Function . . . Basic Channel Default Changed Default Message Altered True Voice Note ON Note OFF Key's Ch's All channels x x x **************** 0 ­127 **************** o o o o o *1 *1 *1 x 1­16 x x x x x x x x x *2 *2 *2 Memorized Mode Note Number : Velocity After Touch Pitch Bend 10 11 0 ­ 119 Control Change o *1 *1 *1 x x x *2 *2 Panpot Expression Messages other than the above Program Change : True # : Quarter Frame : Song Pos : Song Sel : Tune : Clock : Commands o **************** o x x x x o o o o x o x x *1 *1 *3 x 1­6, 21­30 o x x x x x x x x x x x x *2 Program number : 1­11, 21­30, 71­80, 128 System Exclusive System Common System Real Time *4 *1 *1 *1 *1 : All Sounds OFF : Reset All Controllers Aux : Local ON/OFF Messages : All Notes OFF : Active Sensing : System Reset Notes *1 Transmitted only during MIDI phrase playback *2 o x is selectable. Mode 2 : OMNI ON, MONO Mode 4 : OMNI OFF, MONO o : Yes x : No Mode 1 : OMNI ON, POLY Mode 3 : OMNI OFF, POLY 64 AUDIO RECORDER Model AR-200R Date : July. 1, 2006 MIDI Implementation Chart Transmitted Recognized Version : 1. 00 Remarks MIDI Recording Section Function . . . [. . . ]