User manual ROLAND CS-2 ANNEXE 45

[. . . ] Copyright © 2003 Roland CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of Roland CORPORATION. USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. [. . . ] Take the steps below if the height of the divided pickup is not right. 1) Carefully examine the pickup in its current state, and add a suitable number of spacers if the pickup is too low, or remove one or more spacers if the pickup is too high. 3) Remove the divided pickup from the guitar. * Use care in handling the divided pickup; bending or twisting it may cause breaking in the coil elements. Carefully insert something thin and flat (like a table knife) under the Pickup from the sixth string side, then gently pry the pickup upwards. Pickup Spacer Pickup Cushion * * Adjust the pickup cushion thickness as required, for example by using two pickup cushions. The pickup spacers and the pickup cushions are attached to the guitar with double­sided tape. When affixing the tape, however, the tape's thickness is reduced by 0. 1 mm (0. 004") when the backing of the tape is removed. Therefore, when using several pickup spacers, take this fact into account and set the height slightly higher to compensate. fig. 1070 (Removing the Pickup) 10 Attaching the CS-2 to the Guitar 4) After removing the pickup, carefully remove the double­sided tape from the bottom of the pickup. If you wish to add a spacer, first completely remove the used double­ sided tape from the top surface of the existing spacers, then add the new spacer. If you need to remove any spacers, remove the necessary number of spacers and completely remove the remaining double­sided tape from the top surface. Attach two pieces of the new double­sided tape B to the bottom of the pickup. If when mounting the divided pickup you find that double-sided tape B lacks sufficient adhesion, use double-sided tape C. * Using double-sided tape C strongly and securely attaches the pickup. Adjust the height of the pickup. * The pickup height should be adjusted so that the distance between the pickup and the strings is about 1. 0 mm (0. 04") when the highest frets on the first and sixth strings are fingered. Check the height using the supplied clearance gauge (1. 0 mm). If the pickup ends up being too low, use two rubber sheets layered together. But the pickup still sits too low even after layering the two rubber sheets, then use the rubber tubes. * Screw 3 x 8 mm fig. 1105-2e Rubber Sheet Pickup Holder * Tighten the screws until the pickup lightly presses down against the rubber sheet. 2. Remove the strings and the bridge from the guitar. Lower the two bridge height adjustment screws of the guitar approximately 2 mm (0. 08"). * If the bridge is of the type whereby the posts themselves are adjusted, then lower the post height by 2 mm (0. 08"). * Screw 3 x 8 mm Rubber Tube Pickup Holder If the pickup position is too high, insert the included 13-mm washers between the pickup holder and the bridge. 4. Place the holder on the posts, then cover it with the bridge. fig. 1105 (Attachment with the Holders) Neck side Bridge Neck side Bridge Washer Ø13 mm Pickup Holder Bridge Height Adjustment Screw of the Guitar Post End pin side Pickup Holder End pin side Post Bridge Height Adjustment Screw of the Guitar * 5. Restring and tune the guitar. * Tune the strings with the divided pickup adjusted to the optimal position (where all strings ride over their respective yokes). Afterwards, when connecting to GK-compatible devices, you will need to adjust the pickup sensitivity again. However, you may find that the sensitivity level on the GK-compatible device is too high. In such instances, you may be able to correct the problem by widening the clearance between the strings and the pickup, so try lowering the Pickup height slightly to see if this approach is effective. 13 Attaching the CS-2 to the Guitar Checking and Finely Adjusting the Pickup Height Use the clearance gauge to confirm that the clearance between each string and the pickup is about 1 mm. [. . . ] Service Division 22-32 Pun Shan Street, Tsuen Wan, New Territories, HONG KONG TEL: 2415 0911 Parsons Music Ltd. 8th Floor, Railway Plaza, 39 Chatham Road South, T. S. T, Kowloon, HONG KONG TEL: 2333 1863 CENTRAL/LATIN AMERICA ARGENTINA Instrumentos Musicales S. A. Av. Santa Fe 2055 (1123) Buenos Aires ARGENTINA TEL: (011) 4508-2700 U. A. E. Zak Electronics & Musical Instruments Co. TEL: (04) 3360715 MEXICO Casa Veerkamp, s. a. [. . . ]