User manual ROLAND FANTOM XR

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the Roland Fantom-XR. 201b Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. 3­4), and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. [. . . ] Either turn the VALUE dial or use [INC][DEC] to select the write destination. Multisamples consisting of user samples will be written to User, and multisamples consisting of card samples will be written to Card. A message will ask you to confirm the operation. Multisample 128 split (128 key) 7. sample No. 001 original key C3 sample No. 002 sampleNo. 003 ogriginal key C5 : original key split point original key C4 split point When you create a multisample, the split points are automatically determined according to the original key of each sample. Before you begin this process, you should set the original key of each sample to the range where you want it to be assigned. A sample will not sound at a pitch higher than one octave above the original key. 8. fig. 15-019 126 Editing a Sample 9. If you are sure you want to write the multisample, press [ENTER]. Never switch off the Fantom-XR while data is being saved. 10. When the data has been written, the Create Patch screen will appear. If you want to use the multisample as a patch, create the patch as described in step 4 and following of "Creating a Patch from a Sample (Create Patch)" (p. If you don't want to use the multisample as a patch, simply press [EXIT]. * You cannot listen to a multisample unless you assign it to a part as a patch. If you press [EXIT] at this point, the multisample will be saved, but if you want to actually play it, you'll need to assign the saved multisample to a patch using a separate procedure (p. 124). Removing Unwanted Portions of a Sample (Truncate) This operation cuts the portions of the sample that are earlier than the Start Point and later than the Loop End Point. You cannot execute this with more than one sample selected. In the Sample List screen, select the sample that you want to edit. Either press [ENTER], or press [SHIFT] so it lights and then press [SAMPLING]. Set the start point and end point of the sample as described in "Setting the Start/End Points of the Sample" (p. Press [SHIFT] so it lights, and then press The Sample Modify Menu screen will appear. . 2. 3. Assigning a multisample to the desired keys In order to assign a multisample to the desired keys, you'll need to set the Original Key of each sample to the appropriate keys. Then, when you execute the Create Multisample operation, the Fantom-XR will assign the samples to the keyboard and set the split points automatically. In the Sample List screen, select the sample that you want to include in your new multisample. Use or to select "Sample Parameter. " 4. 6. Alternatively, you can press [ENTER] to access the screen. [. . . ] NSW 2099 AUSTRALIA TEL: (02) 9982 8266 SAUDI ARABIA aDawliah Universal Electronics APL Corniche Road, Aldossary Bldg. , 1st Floor, Alkhobar, SAUDI ARABIA P. O. Box 2154, Alkhobar 31952 SAUDI ARABIA TEL: (03) 898 2081 RUSSIA MuTek 3-Bogatyrskaya Str. 1. k. l 107 564 Moscow, RUSSIA TEL: (095) 169 5043 Roland Shanghai Electronics Co. , Ltd. No. 18 Anhuaxili Chaoyang District, Beijing 100011 CHINA TEL: (010) 6426-5050 BELGIUM/HOLLAND/ LUXEMBOURG Roland Benelux N. V. Houtstraat 3, B-2260, Oevel (Westerlo) BELGIUM TEL: (014) 575811 SPAIN Roland Electronics de España, S. [. . . ]