User manual ROLAND GR-55

[. . . ] . 4 5 6 7 8 Reference Panel Descriptions . 21 Settings Preparations for Using the GR-55 . 8 Selecting Guitar or Bass (GUITAR<->BASS). 11 Specifying the Output System (OUTPUT SELECT) . [. . . ] POLARITY INVERSE The left and right phase will be opposite. When using a mono source, this spreads the sound. The left and right phase will be the same. Select this when inputting a stereo source. Adjusts the proportion of the phaser sound that is fed back into the effect. Negative (-) settings will invert the phase. Adjusts the rate of the stepwise change in the phaser effect. Adjusts the level of the phaseshifted sound. Adjusts the output volume. L in R in Parameter Tremolo Tremolo Value TRI SQR SIN 2-Band EQ 2-Band EQ L out R out Description Triangle wave Square wave Sine wave Sawtooth wave SYNCHRO RESONANCE # CROSS FEEDBACK STEP RATE # MIX LOW GAIN HIGH GAIN LEVEL 0­100 -98­+98% Specifies how the volume will be modulated. MOD WAVE # 0­100, BPM ­ 0­100 -15­+15 dB -15­+15 dB 0­100 SAW1/2 SAW1 SAW2 RATE # DEPTH # LOW GAIN 0­100, BPM ­ 0­100 -15­+15 dB -15­+15 dB 0­100 Adjusts the frequency of the change. Adjusts the output volume. 05: RING MODULATOR This is an effect that applies amplitude modulation (AM) to the input signal, producing bell-like sounds. You can also change the modulation frequency in response to changes in the volume of the sound sent into the effect. HIGH GAIN LEVEL L in Ring Mod 2-Band EQ L out 07: AUTO PAN Cyclically varies the stereo location of the sound. R in Ring Mod Value 0­127 0­100 2-Band EQ R out Description Adjusts the frequency at which modulation is applied. Adjusts the amount of frequency modulation applied. L in R in Auto Pan Auto Pan Value TRI SQR SIN 2-Band EQ 2-Band EQ L out R out Description Triangle wave Square wave Sine wave Sawtooth wave Parameter FREQUENCY # SENS # Parameter Specifies how the pan position will be varied. POLARITY Determines whether the frequency modulation moves towards higher frequencies or lower frequencies. UP DOWN Higher frequencies Lower frequencies Adjusts the gain of the low frequency range. Adjusts the gain of the high frequency range. Adjusts the volume balance between the direct sound (D) and the effect sound (W). MOD WAVE SAW1/2 LOW GAIN HIGH GAIN BALANCE # LEVEL -15­+15 dB -15­+15 dB D100:0W­D0:100W 0­100 SAW1 R SAW2 R L RATE # DEPTH # LOW GAIN HIGH GAIN LEVEL 0­100, BPM ­ 0­100 -15­+15 dB -15­+15 dB 0­100 L Adjusts the frequency of the change. Adjusts the output volume. 47 Effect Settings (EFFECT) 08: SLICER By applying successive cuts to the sound, this effect turns a conventional sound into a sound that appears to be played as a backing phrase. This is especially effective when applied to sustain-type sounds. Parameter SPREAD LOW GAIN HIGH GAIN LEVEL Value 0­10 -15­+15 dB -15­+15 dB 0­100 Description Specifies how the sound of the rotary speaker will be spread. Adjusts the output volume. L in Slicer L out R in Parameter PATTERN # RATE # ATTACK # Slicer Value P01­P20 0­100, BPM ­ 0­100 R out Description Selects the slice pattern used to cut the sound. Specifies the rate at which the 16-step sequence will repeat. Adjusts the speed at which the level changes between steps. [. . . ] Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 2493 9051 U. Eastern Avenue Los Angeles, CA 90040-2938, U. TEL: (323) 890 3700 CHILE Comercial Fancy II S. A. Rut. : 96. 919. 420-1 Nataniel Cox #739, 4th Floor Santiago - Centro, CHILE TEL: (02) 688-9540 ITALY Roland Italy S. [. . . ]