User manual ROLAND HP-337 V1.00 MIDI IMPLEMENTATION

[. . . ] DIGITAL PIANO Model HP-337 MIDI Implementation rPortamento Time (Controller number 5) Status BnH 2nd bytes 05H 3rd byte vvH Date: Apr. Receive data sChannel Voice Messages qNote off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H n = MIDI channel number: 0H-FH (ch. 1-ch. 16) vv = Portamento Time: 00H-7FH (0-127), Initial value = 00H (0) * This adjusts the rate of pitch change when Portamento is ON or when using the Portamento Control. A value of 0 results in the fastest change. n = MIDI channel number: 0H-FH (ch. 1-ch. 16) kk = note number: 00H-7FH (0-127) vv = note off velocity: 00H-7FH (0-127) * * For Drum Parts, these messages are received when Rx. NOTE OFF = ON for each Instrument. The velocity values of Note Off messages are ignored. rData Entry (Controller number 6, 38) Status BnH BnH 2nd bytes 06H 26H 3rd byte mmH llH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) mm, ll = the value of the parameter specified by RPN/NRPN mm = MSB, ll = LSB qNote on Status 9nH 2nd bytes kkH 3rd byte vvH rVolume (Controller number 7) Status BnH 2nd bytes 07H 3rd byte vvH n = MIDI channel number: 0H-FH (ch. 1-ch. 16) kk = note number: 00H-7FH (0-127) vv = note on velocity: 01H-7FH (1-127) * * Not received when Rx. NOTE MESSAGE = OFF. [. . . ] 00 00 01 00-07 REVERB MACRO 00: Room 1 01: Room 2 02: Room 3 03: Hall 1 04: Hall 2 05: Plate 06: Delay 07: Panning Delay 0-7 0-7 0-127 0-127 0-127 04 Hall 2 40 01 30 40 01 31 40 01 32 40 01 33 40 01 34 40 01 35 * * 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-07 00-07 00-7F 00-7F 00-7F REVERB CHARACTER REVERB PRE-LPF REVERB LEVEL REVERB TIME REVERB DELAY FEEDBACK 04 00 40 40 00 4 0 64 64 0 REVERB MACRO is a macro parameter that allows global setting of reverb parameters. When you select the reverb type with REVERB MACRO, each reverb parameter will be set to the most suitable value. REVERB CHARACTER is a parameter that changes the reverb algorithm. The value of REVERB CHARACTER corresponds to the REVERB MACRO of the same number. 9 40 01 38 00 00 01 00-07 CHORUS MACRO 40 01 39 40 01 3A 40 01 3B 40 01 3C 40 01 3D 40 01 3E 40 01 3F * 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-07 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F CHORUS PRE-LPF CHORUS LEVEL CHORUS FEEDBACK CHORUS DELAY CHORUS RATE CHORUS DEPTH CHORUS SEND LEVEL TO REVERB 00: Chorus 1 01: Chorus 2 02: Chorus 3 03: Chorus 4 04: Feedback Chorus 05: Flanger 06: Short Delay 07: Short Delay (FB) 0-7 0-127 0-127 0-127 0-127 0-127 0-127 02 Chorus 3 00 40 08 50 03 13 00 0 64 8 80 3 19 0 CHORUS MACRO is a macro parameter that allows global setting of chorus parameters. When you use CHORUS MACRO to select the chorus type, each chorus parameter will be set to the most suitable value. qPart Parameters HP-337 has 16 parts. Parameters that can be set individually for each Part are called Part parameters. If you use exclusive messages to set Part parameters, specify the address by Block number rather than Part Number (normally the same number as the MIDI channel). The Block number can be specified as one of 16 blocks, from 0 (H) to F (H). The relation between Part number and Block number is as follows. x. . . BLOCK NUMBER (0-F), Part 1 (MIDI ch = 1) x = 1 Part 2 (MIDI ch = 2) x = 2 : : : Part 9 (MIDI ch = 9) x = 9 Part10 (MIDI ch = 10) x = 0 Part11 (MIDI ch = 11) x = A Part12 (MIDI ch = 12) x = B : : : Part16 (MIDI ch = 16) x = F Data (H) 00-7F 00-7F 00-10 00-01 00-01 00-01 00-01 00-01 00-01 00-01 00-01 Parameter TONE NUMBER Rx. VALUE 1-128 1-16, OFF OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON Default Value (H) Description 00 0 00 1 Same as the Part Number 01 ON 01 ON 01 ON 01 ON 01 ON 01 ON 01 ON 00 (01*) OFF (ON*) Address (H) 40 1x 00 40 1x 01# 40 1x 02 40 1x 03 40 1x 04 40 1x 05 40 1x 06 40 1x 07 40 1x 08 40 1x 09 40 1x 0A * Size (H) 00 00 02 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 When "GM1 System On" and "GM2 System On" are received, Rx. When "GS Reset" is received, it will be set ON. 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-01 00-01 00-01 00-01 00-01 00-01 00-01 00-01 00-01 00-02 Rx. SOFT MONO/POLY MODE (= CC# 126 01 / CC# 127 00) ASSIGN MODE OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON OFF/ON Mono/Poly 0 = SINGLE 1 = LIMITED-MULTI 2 = FULL-MULTI 01 01 01 01 01 01 01 01 01 00 at x = 0 01 at x 0 ON ON ON ON ON ON ON ON Poly SINGLE at x = 0 LIMITED-MULTI at x 0 40 1x 0B 40 1x 0C 40 1x 0D 40 1x 0E 40 1x 0F 40 1x 10 40 1x 11 40 1x 12 40 1x 13 40 1x 14 * ASSIGN MODE is the parameter that determines how voice assignment will be handled when sounds overlap on identical note numbers in the same channel (i. e. , repeatedly struck notes). This is initialized to a mode suitable for each Part, so for general purposes there is no need to change this. 00 00 01 00-02 USE FOR RHYTHM PART 0 = OFF 1 = MAP1 2 = MAP2 00 at x 0 01 at x = 0 OFF at x 0 MAP1 at x 0 40 1x 15 * This parameter sets the Drum Map of the Part used as the Drum Part. HP-337 can simultaneously (in different Parts) use up to two Drum Maps (MAP1, MAP2). With the initial settings, Part10 (MIDI CH = 10, x = 0) is set to MAP1 (1), and other Parts are set to normal instrumental Parts (OFF (0)). 00 00 01 00 00 02 28-58 08-F8 PITCH KEY SHIFT PITCH OFFSET FINE -24 - +24 [semitones] -12. 0 - +12. 0 [Hz] Use nibblized data. 40 08 00 0 [semitones] 0 [Hz] 40 1x 16 40 1x 17 40 1x 18# * PITCH OFFSET FINE allows you to alter, by a specified frequency amount, the pitch at which notes will sound. This parameter differs from the conventional Fine Tuning (RPN #1) parameter in that the amount of frequency alteration (in Hertz) will be identical no matter which note is played. When a multiple number of Parts, each of which has been given a different setting for PITCH OFFSET FINE, are sounded by means of an identical note number, you can obtain a Celeste effect. 10 40 1x 19 40 1x 1A 40 1x 1B 40 1x 1C 40 1x 1D 40 1x 1E 40 1x 1F 40 1x 20 40 1x 21 40 1x 22 40 1x 23 * * * 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00 00 01 00-7F 00-7F 00-7F 00-7F 00-7F 00-7F 00-5F 00-5F 00-7F 00-7F 00-01 PART LEVEL 0-127 (= CC# 7) VELOCITY SENSE DEPTH 0-127 VELOCITY SENSE OFFSET 0-127 PART PANPOT -64 (RANDOM), -63 (LEFT) - +63 (RIGHT) (= CC# 10, except RANDOM) KEY RANGE LOW (C-1)-(G9) KEY RANGE HIGH (C-1)-(G9) CC1 CONTROLLER NUMBER 0-95 CC2 CONTROLLER NUMBER 0-95 CHORUS SEND LEVEL 0-127 (= CC# 93) REVERB SEND LEVEL 0-127 (= CC# 91) Rx. [. . . ] The values of RPN #1 (Master Fine Tuning) and System Exclusive MASTER TUNE are added together to determine the actual pitch sounded by each Part. Frequently used tuning values are given in the following table for your reference. Values are in hexadecimal (decimal in parentheses). +----------------+----------------+----------------------------+--------------------------------------+ |Hz in A4| cent | RPN #1 | Sys. Ex. [. . . ]