User manual ROLAND JUPITER-4 SERVICE MANUAL

[. . . ] Install in accordance with the manufacturers instructions. Do not install near any heat sources such as radiators, heat registers, stoves, or other apparatus (including amplifiers) that produce heat. Do not defeat the safety purpose of the polarized or grounding-type plug. A polarized plug has two blades with one wider than the other. [. . . ] · The Transpose function does not apply to Drums/SFX or Manual Percussion. 50 Introduction Playing Sounds Editing Sounds Other Convenient Functions Connecting Other Equipment Appendix Editing Sounds Editing a Registration A Registration stores the sounds selected for each Part, as well as various performance-related settings. 30) shows basic information about the currently selected Registration. Percussion tone name Registration name Solo tone name Basic Operation for Registration Editing 1. In the Registration screen (p . 30), touch Registration's <EDIT> . Access the Live Set screen Upper Live Set name Lower Live Set name The Registration Part screen will appear. The Registration saves the following parameters. Tab Explanation Part-related settings · Registration Level PART · The Live Sets assigned to the Upper Part and Lower Part · The Tones assigned to the Solo Part and Percussion Part · Each Part's octave, pan, volume, etc. Settings common to the entire Registration · Registration name · Registration Level · Tempo COMMON/ CONTROL · Split · D Beam controller, [S1]/[S2] button, and [E1]­[E4] knob assignments · Arpeggiator · Harmony Intelligence · Control and other data sent to each Part · Octave Shift, Transpose, etc. Settings for the Percussion Part or Solo Part · Tone, pan, volume, and reverb send level · Keyboard range · Pitch PERC PART, SOLO PART · Vibrato · Offset values for filter and envelope · Velocity · Mono/poly switch · Legato · Voice reserve (guaranteed polyphony) · Control data received by each Part, etc. EFFECTS EXT PART Effects for the Percussion Part and Solo Part Settings for messages sent to external MIDI devices 2. Touch a tab to select the Registration parameters that you want to edit . Tabs MEMO If a Registration has been edited, a check mark (red) will appear at the right of the Registration name. Let's try editing these parameters. 52 Editing a Registration Saving a Registration Edits you make to a Registration are temporary; they will be lost when you turn off the power or select another Registration. If you want to keep an edited Registration, you must save it. NOTE When you execute the Write operation, the existing data at the write destination will be overwritten. REFERENCE For details on how a Registration is structured, refer to "How Registrations are Organized" (p. 15). 3. Press the blinking Registration button . A message will ask "Are you sure?" MEMO You can also save by touching <WRITE> in the Registration Write screen. 4. To write the data, touch <OK> . The message "Completed!" will appear. NOTE Never turn off the power while data is being saved. Introduction 1. In the Registration screen (p . Editing will be easier if you're listening only to the Parts that are selected for the Live Set you want to edit (p. 37). Level of each layer. View the Live Set Common screen. View the Live Set Effects screen. MEMO When you edit the parameters of a Live Set, you are specifying a relative increase or decrease applied to the value of the Tone; the actual tone itself is not affected. This means that even if the same tone is used by another Live Set, you'll be able to edit without affecting the other Live Set. Basic Editing Operations for Live Sets To edit a Live Set, you'll start from the Live Set screen. View the Live Registration screen. Tone name Switch between the Upper Part and Lower Part 1. In the Live Set screen (p . 32), touch the button (<COMMON>, <LAYER>, <EFFECTS>) of the parameter that you want to edit . The following parameters are stored in a Live Set. Tab Explanation Settings common to the entire Live Set · Live set name, Live Set category COMMON · Volume · Filter · Phase lock, etc. Settings for each layer · Layer on/off LAYER · Volume · Pan · Layer audio output destination and send level · Keyboard range, etc. MFX settings · Layer audio output destination and send level · Send level to MFX · MFX on/off EFFECTS · MFX type selection · MFX volume · MFX settings, reverb settings · Send levels from the Tone to reverb, and from MFX to reverb, etc. Offset settings for each layer For a SuperNATURAL Synth Tone · Pitch MODIFY · Filter · Amp · LFO · Modulation · Portamento, etc. For a SuperNATURAL Acoustic Tone · Noise level · Variation, etc. Tabs 2. Touch a tab to select the Live Set parameters that you want to edit . In this example, the Upper Part's Live Set is edited. 56 Editing a Live Set MEMO If a Live Set has been edited, a check mark (red) will appear at the right of the Live Set name. Changing a Live Set's Tones Here's how to change the Tones in a Live Set. 1. In the Live Set screen (p . 32), touch a tone name to view a list . MEMO You can also switch tones by moving the cursor to the tone name in the Live Set screen, and using the value dial or the [DEC] [INC] buttons to select a Tone. Introduction Adjusting the Tones By touching <EDIT> of each layer in the Live Set screen (p. [. . . ] TEL: (868) 638 6385 JORDAN MUSIC HOUSE CO. Box 922846 Amman 11192, JORDAN TEL: (06) 5692696 COSTA RICA JUAN Bansbach Instrumentos Musicales Ave. 1. Calle 11, Apartado 10237, San Jose, COSTA RICA TEL: 258-0211 KOREA Cosmos Corporation 1461-9, Seocho-Dong, Seocho Ku, Seoul, KOREA TEL: (02) 3486-8855 POLAND ROLAND POLSKA SP. Kty Grodziskie 16B 03-289 Warszawa, POLAND TEL: (022) 678 9512 URUGUAY Todo Musica S. A. [. . . ]