User manual ROLAND JUPITER-80

[. . . ] WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. Do not block any of the ventilation openings. [. . . ] The Registration Write screen will appear. The [WRITE] button will light, and the Registration buttons will blink. MEMO You can also perform a save by touching Registration screen's <WRITE>. Editing Sounds For details on assigning a name, refer to "Assigning a Name" (p. 29). Other Convenient Functions 2. Move the cursor to Write Destination, and use the value dial or the [DEC] [INC] buttons to select the write destination . Registration number Connecting Other Equipment Appendix MEMO You can also use the bank buttons ([A]­[D]) and Registration buttons ([1]­[8]) to directly specify the write destination. 53 Editing a Registration If the following display appears when you save If Live Set parameters or SuperNATURAL Synth Tone parameters have been edited, the corresponding Live Set or SuperNATURAL Synth Tone will be highlighted when you save the Registration. 2. If you want to specify the Live Set number or SuperNATURAL Synth Tone number for saving, touch <SELECT DEST> . Live Set Select Destination screen will appear. The Synth Tone has been edited. The Live Set has been edited. 3. Select the write destination . 1 Select the write destination for the Live Set. 2 You have the option of saving the edited Live Sets and SuperNATURAL Synth Tones at the same time that you save the Registration. If you want to do this, proceed as follows. Select the write destination for the SuperNATURAL Synth Tone. 1. Select the Write check box for the Live Sets and SuperNATURAL Synth Tones that you want to save . 3 Confirm selections and return to the previous screen. 4. Touch <WRITE> . MEMO · If you specify the same write destination for the Live Sets of the Upper Part and Lower Part, the message "Cannot Write!" will appear. Select different write destinations in step 3. · If you specify the same write destination for the SuperNATURAL Synth Tones of layers 1­4, the message "Cannot Write!" will appear. Select different write destinations in step 3. · If the same Live Set is assigned to the Upper Part and the Lower Part, and you edit only one Part and then execute this operation, the edited Live Set will be assigned to the other Part as well. · If the same SuperNATURAL Synth Tone is assigned to layers 1­4, and you edit only the SuperNATURAL Synth Tone of a specific layer and then execute this operation, the edited SuperNATURAL Synth Tone will also be assigned to the other layers. MEMO If you save without selecting these check boxes, only the Registration will be saved. The Live Sets or SuperNATURAL Synth Tones you've edited will remain in their edited state without being saved. If you want to specify a Live Set number or SuperNATURAL Synth Tone number at which to save the data, proceed to step 2. If you want to save the data by overwriting the current Live Set number and SuperNATURAL Synth Tone number, proceed to step 4. 54 Editing a Registration Initializing a Registration Here's how to initialize the currently selected Registration. MEMO · Initializing the Registration will affect the data in the temporary area (p. When you initialize the Registration, the Live Sets and tones in the temporary area will also be initialized. · If you want to return the parameters of all sounds to their factory-set state, use Factory Reset (p. 87). Introduction 1. In the Registration Part screen (p . 31), touch <UTILITY> . Playing Sounds Registration Utility Menu screen will appear. Editing Sounds 2. Touch <Registration Initialize>, and then touch <Select> . Other Convenient Functions A message will ask "Are you sure?" 3. Connecting Other Equipment Touch <OK> . Appendix 55 Editing a Live Set You can edit a Live Set by switching the Tones in the Live Set, and by adjusting offset values relative to the value of each tone. 32) shows basic information about the currently selected Live Set. View the Live Set Effects Routing screen. Tips for editing a Live Set Choose which Parts will be heard A Registration consists of up to four Parts. Editing will be easier if you're listening only to the Parts that are selected for the Live Set you want to edit (p. 37). Level of each layer. View the Live Set Common screen. View the Live Set Effects screen. MEMO When you edit the parameters of a Live Set, you are specifying a relative increase or decrease applied to the value of the Tone; the actual tone itself is not affected. [. . . ] Francisco Acuna de Figueroa 1771 C. P. : 11. 800 Montevideo, URUGUAY TEL: (02) 924-2335 KUWAIT EASA HUSAIN AL-YOUSIFI & SONS CO. Al-Yousi Service Center P. O. Box 126 (Safat) 13002, KUWAIT TEL: 00 965 802929 MALAYSIA/ SINGAPORE Roland Asia Paci c Sdn. 45-1, Block C2, Jalan PJU 1/39, Dataran Prima, 47301 Petaling Jaya, Selangor, MALAYSIA TEL: (03) 7805-3263 CURACAO Zeelandia Music Center Inc. Orionweg 30 Curacao, Netherland Antilles TEL: (305) 5926866 PORTUGAL Roland Systems Group EMEA, S. L. [. . . ]