User manual ROLAND JV1080 SUPPLEMENTAL NOTES

[. . . ] ^ February 20, 1997 jv-1080 super jv sound module Supplemental Notes SN67 Ver 1. 0 MIDI Sequencing with the Roland JV-1080 The Roland JV-1080 is a 64-voice polyphonic, 16-Part multitimbral synthesizer sound module. It includes 512 instrument sounds and 8 drum kits. It also has three sets of stereo outputs and 40 digital effects including chorus, rotary speaker, distortion, reverb, and delay. This supplement is a basic guide for using the Roland JV-1080 in combination with other MIDI instruments such as MIDI keyboards and sequencers. [. . . ] Recording Part 2 to your Sequencer Now that weve recorded MIDI channel 1 data to track 1 of your sequencer using JV-1080 Performance Part 1, lets use Part 2 to record MIDI channel 2 to track 2 of your sequencer. Weve already determined that Part 2 in this Performance is using the Patch selected in step 5 above. From the previous display, use the following procedure to record Part 2: 1) 2) 3) 4) Select track 2 on your sequencer and enable it for recording. Set the MIDI channel on your keyboard and/or sequencer to MIDI channel 2. Start recording on your sequencer and play your keyboard. Playback your song from the beginning to hear the results. Recording Part 10 (the Drum Part) to your Sequencer Any Rhythm Kit in the JV-1080 can be used in a Performance. As such, Part 10 is set to MIDI channel 10. Use the following procedure to record a drum track: 1) 2) 3) 4) 5) 6) 7) 8) Make sure the PERFORM, PARAMETER, PART (4/12), and PALETTE buttons are lit. Press the [1]-[8]/[9]-[16] button, so it is lit. This will display Performance Parts 9 to 16. Use the LEFT/RIGHT CURSOR buttons to select Part 10. Use the UP/DOWN CURSOR buttons to select the PATCH GROUP screen. Use the VALUE knob or the DEC/INC buttons to select a Bank (USR, PRA, PRB, PRC, GM). Press the DOWN CURSOR button to select the PATCH NUMBER page and use the VALUE knob to select a drum kit (1 or 2). Set the MIDI channel on your keyboard and/or sequencer to MIDI channel 10. Start recording on your sequencer and play your keyboard. Playback your song from the beginning to hear the results. Naming and Saving a Performance Now that we have a Performance setup the way we want, lets name it and save it to a User location. Use the following procedure to give your Performance a name: 1) Press PARAMETER, so it is lit, then press the COMMON (1/9) button. Make sure that the PALETTE button is not lit. 1 2) Use the UP CURSOR button to select the PERFORM NAME screen. 3) Use the CURSOR buttons to select the character you wish to change and the VALUE knob to select the desired letter. 4) Press UTILITY. 1997 Roland Corporation U. S. MIDI Sequencing with the Roland JV-1080 Page 6 of 10 ^ JV-1080 Supplemental Notes 5) Use the CURSOR buttons to select WRITE (it should start to flash). The destination of your custom Performance (USR: 12 Orchestral) will be displayed. [. . . ] 7) Use the UP/DOWN CURSOR buttons to access the PATCH EFX CTRL screen. 8) The two rotary (Leslie speaker) effect parameters that can be controlled in real-time are speed and level. Use the LEFT CURSOR button to underline MODULATION (the parameter currently assigned to control the rotary speed) and use the VALUE knob to select SYS-CTRL1. 9) Assign a slider (or foot pedal) on your keyboard to transmit controller 16 to the JV-1080, it will control the rotation speed of the Rotary effect. TIP: You can assign both speed and level to SYS-CTRL1 so that when you send CC:16 to the JV-1080, the rotary speed and level will change simultaneously. [. . . ]