User manual ROLAND JX-305

[. . . ] 5 Operating requirements . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Installing JX-305. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 Uninstalling JX-305 . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 6 About the RSS M-400 driver . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] This button is shown in blue while the SCENE screen is displayed. Recalls the mixer parameters from the currently selected scene number. Stores the current mixer parameters to the selected scene number. 11 Names of things and what they do 5 Fader layer buttons fig. ScrLayer. eps These buttons switch the layer operated by fader modules 1­24. The currently selected layer is shown in blue. SENDS ON FADER button CH1-24 button CH25-48 button AUX/MTX button or AUX/DCA button Accesses the SENDS ON FADER panel. Assigns CH1­CH24 to fader modules 1­24. Assigns CH25­CH48 to fader modules 1­24. Assigns AUX1­AUX16 and MATRIX1­MATRIX8, or AUX1­AUX16 and DCA1­DCA8 to fader modules 1­24. 6 Fader modules 1­24 fig. ScrFader1-24. eps Use these faders to operate the input channels, AUX channels, MATRIX channels, and DCA channels. SEL button SOLO button MUTE button Fader Selects the corresponding channel. The button of the selected channel is shown in green. The button is shown in orange if Solo is on. The button is shown in red if Mute is on. Adjusts the signal level of the channel. Adjustments made to a selected channel strip in M380RCS will be reflected in the appropriate M-380 channel strip, but the M-380 display will not switch its display to your selected channel strip in the JX-305. 7 Main fader module fig. ScrFaderMain. eps Toggling the SEL button, you will alternate between selecting the MAIN L channel and the MAIN R channel. This fader controls the MAIN L/R. SEL button SOLO button Fader Selects the MAIN L/R channel. If you select the "Send User Libraries" option, the user library will be sent from M380RCS to the M-380 console. 4 "Send User Libraries" will overwrite current libraries unless they are locked. Be sure to lock or save any needed M380 libraries to USB memory prior to sending. Click "OK. " If you selected "Read from CONSOLE" in step 2, the current project will be closed, a new project will be opened, and then synchronization will begin. A message box will ask whether you want to save the current project. fig. ScrSyncConfirm. eps · If you click "Yes, " the current project will be saved (by overwriting). · If you click "No, " the current project will not be saved. · If you click "Cancel, " project synchronization will be cancelled. If you selected "Send to CONSOLE" in step 2, a message box will ask you to confirm the project synchronization. 20 Using JX-305 fig. ScrSyncConfirm2. eps When you click "OK, " project synchronization will begin. 5 When project synchronization is completed, JX-305 will switch to online mode. fig. ScrOnline. eps The M-380 console will show a progress message while the project is being synchronized. Operations on the M-380 will be disabled during this time. In online mode, you'll be able to remotely control the M-380 console from JX-305. If you selected "Send to CONSOLE" in step 2 and the M-380's scene memory or user library contains any locked data, a message box will ask you whether you want to overwrite the data. If you click "OK, " the data will be overwritten. If you click "Cancel, " project synchronization will be cancelled. fig. ScrSyncConfirmLock1. eps 21 Using JX-305 Switching to offline mode 1 Click the ONLINE button. fig. ScrOnline. eps 2 JX-305 will switch to offline mode. fig. ScrOffline. eps 22 Using JX-305 REAC input/output settings In offline mode, you can make virtual settings for an input/output unit (e. g. , S-1608 stage unit, S-0816 FOH unit, S-4000S 40-channel I/O modular rack) that will later be connected to the M-380 console. This lets you make preamp gain settings or input/ output patching ahead of time, to specify the M-380's input/output settings that will be used at the actual performance. Settings in the REAC Config dialog box are used to supplement offline mode. When you load a project on the M-380 console itself, or switch to online mode, the settings for the input/output units that are actually connected to the M380 will be applied. 1 From the "Setup" menu, choose "REAC Config. " fig. ScrReacConf. eps The "REAC Config" dialog box is unavailable in online mode. The "REAC Config" dialog box will appear. 2 3 Access the "REAC A tab" (or "REAC B" tab). From the pulldown menu, select the input/output unit that you will connect to REAC A (or REAC B). [. . . ] The M-48 library data in JX-305 can be recalled to a physical M-48 unit. ( "Switching to online mode" (p. 20)) You cannot perform the following operations for the "Virtual" unit. · Edit the unit name "Virtual" · Store or recall memories · Set the MEMORY SAFE function, or make output mute settings M-48 settings in online mode The M-48 MANAGER popup will show the M-48 units that are actually connected. [. . . ]