User manual ROLAND MV-8800

[. . . ] Owner's Manual Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (Owner's Manual; p. 2), "USING THE UNIT SAFELY" (Owner's Manual; p. 4­5), and "IMPORTANT NOTES" (Owner's Manual; p. These sections provide important information concerning the proper operation of the unit. [. . . ] Press [EFFECTS]. The EFFECTS screen (Screen Guide; p. Use CURSOR [ ][ ] to move the cursor to MFX, making it the current effect. MFX will be enclosed in a frame and highlighted. 3. Use the VALUE dial to change the setting of the Routing parameter. This sets the MFX routing. Value Off Input AUX1­4 Master Routing and result MFX will not be used. The effect will apply to the signal received from the input jack. MFX will be routed to AUX bus mixer 1­4 respectively. The internal AUX buses will be used, letting you use MFX as a loop-type effect. MFX will be routed to the master out, and will process all of the sounds mixed together. If the Routing parameter is set to Input The MFX will be routed to the input of the mixer. Since this setting allows you to apply an effect to the input sound, such as the signal arriving via an analog input, it is useful when sampling or recording to an audio track. If the Routing parameter is set to AUX 1 The MFX will be routed to the AUX 1 of the mixer. With this setting, you can set the Output Assign parameter of audio tracks or instruments to AUX 1, and apply the effect to their combined output. If the Routing parameter is set to Master The MFX will be routed to the master out. Since this setting applies the effect to the mixed sound of all outputs, it is appropriate when you want to use the MFX as a master effect. 12 Using effects Applying an effect to the sound from an input Here's how to apply an effect to the input audio, such at that received via the analog inputs. 1. Press [EFFECTS]. The EFFECTS screen will appear. 2. Use CURSOR [ ][ ] to move the cursor to MFX. 3. Set the Routing parameter to "Input. " The effect will be applied to the input audio. MV-8800 Owner's Manual M-215 Changing the MFX routing Applying MFX to an instrument or audio track fig. 11-10. j AUX Instruments/ Audio Phrase/ Audio Track MFX MIX MASTER OUT 1. Press [EFFECTS]. The EFFECTS screen will appear. 2. Press [MIXER]. ][ ] to move the cursor to MFX. 3. Set the Routing parameter to "AUX1. " The MIXER screen will appear. 5. Access the MIXER screen for the instrument or audio track to which you want to apply the effect. 6. Set the Output parameter to "AUX1" for the part on which you want to use MFX. The audio of the instrument or audio track will be sent to AUX bus 1, and the effect will be applied. Applying an effect to the master out fig. 11-10. j MIX Input Instruments/ Audio Phrase/ Audio Track MFX MASTER OUT 1. Press [EFFECTS]. The EFFECTS screen will appear. 2. Use CURSOR [ ][ ] to move the cursor to MFX. 3. Set the Routing parameter to "Master. " The effect will be applied to master out. M-216 MV-8800 Owner's Manual Analog Modeling Bass Analog Modeling Bass is an algorithm that replicates the operation of an analog synthesizer. If you control the parameters with the Velocity Pads or externally with MIDI messages, you can get analog synthesizer sounds with the virtual VCO (Voltage Controlled Oscillator). [. . . ] TEL: (868) 638 6385 ITALY Roland Italy S. Viale delle Industrie 8, 20020 Arese, Milano, ITALY TEL: (02) 937-78300 ISRAEL Halilit P. Tel-Aviv-Yafo ISRAEL TEL: (03) 6823666 As of November 1, 2006 (ROLAND) M-338 MV-8800 Owner's Manual For EU Countries This product complies with the requirements of European Directives EMC 89/336/EEC and LVD 73/23/EEC. For the USA FEDERAL COMMUNICATIONS COMMISSION RADIO FREQUENCY INTERFERENCE STATEMENT This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. [. . . ]