User manual ROLAND RS-70 MANUAL 2

[. . . ] Owner's Manual Thank you, and congratulations on your choice of the Roland RS-70. 201a Before using this unit, carefully read the sections entitled: "USING THE UNIT SAFELY" (p. 2­ 3) and "IMPORTANT NOTES" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's manual should be read in its entirety. [. . . ] NORMAL: The left delay sound will be fed back into the left delay, and the right delay sound into the right delay. CROSS: The left delay sound will be fed back into the right delay, and the right delay sound into the left delay. Adjusts the time from the direct sound until when the left delay sound is heard. Adjusts the time from the direct sound until when the right delay sound is heard. Adjusts the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase. Adjusts the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS. Adjusts the spatial spread of the sound. Adding effects Parameter Low Gain High Gain Balance # Value -15­ +15 [dB] -15­ +15 [dB] D100:0W­ D0:100W Level 0­127 Description Adjusts the gain of the low frequency. Adjusts the volume balance between the direct sound and the modulation delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the modulation delay sound will be output. Adjusts the output level. Parameter Balance # Value D100:0W­ D0:100W Level 0­127 Description Adjusts the volume balance between the direct sound and the delay sound. With a setting of D100:0W only the direct sound will be output, and with a setting of D0:100W only the delay sound will be output. Adjusts the output level. 21: 4 TAP DELAY (Quadruple Tap Delay) The Quadruple Tap Delay has four delays. fig. MFX-21a 20: 3 TAP DELAY (Triple Tap Delay) The Triple Tap Delay produces three delay sounds; center, left and right. fig. MFX-20 Balance D L in Delay 1 Feedback Delay 2 L out Balance W Balance D L in Left Tap Triple Tap Delay Feedback Center Tap 2-Band EQ Balance W L out Quadruple Tap Delay Delay 3 Delay 4 Balance W R in Balance D Balance W R out Right Tap Balance D The stereo location of each delay sound is as follows. R in 2-Band EQ R out fig. MFX-21b 2 1 L 3 4 R Parameter Delay Left Value 0­840 [ms], note *1 0­840 [ms], note *1 0­840 [ms], note *1 -98­ +98 [%] Delay Right Delay Center Feedback # HF Damp 200­8000 [Hz], BYPASS Left Level Right Level Center Level Low Gain High Gain 0­127 0­127 0­127 -15­ +15 [dB] -15­ +15 [dB] Description Adjusts the time delay from the direct sound until when the left delay sound is heard. Adjusts the time delay from the direct sound until when the right delay sound is heard. Adjusts the time delay from the direct sound until when the center delay sound is heard. Adjusts the proportion (%) of the delay sound that is fed back into the effect. Negative (-) settings will invert the phase. Adjusts the frequency above which sound fed back to the effect will be cut. If you do not want to cut the high frequencies of the feedback, set this parameter to BYPASS. Adjusts the volume of the left delay sound. Adjusts the volume of the right delay sound. [. . . ] 1. k. l 107 564 Moscow, RUSSIA TEL: (095) 169 5043 EUROPE AUSTRIA Roland Austria GES. M. B. H. Siemensstrasse 4, P. O. Box 74, A-6063 RUM, AUSTRIA TEL: (0512) 26 44 260 Roland Shanghai Electronics Co. , Ltd. No. 18 Anhuaxili Chaoyang District, Beijing 100011 CHINA TEL: (010) 6426-5050 AUSTRALIA/ NEW ZEALAND AUSTRALIA Roland Corporation Australia Pty. , Ltd. 38 Campbell Avenue Dee Why West. NSW 2099 AUSTRALIA TEL: (02) 9982 8266 SPAIN Roland Electronics de España, S. [. . . ]