User manual ROLAND SRJV80-05

[. . . ] EQ:LowType (Low Type) Shlv, Peak EQ:HiType (High Type) Shlv, Peak Selects the type of the low range (Low) and high range (High) equalizer. (Shlv: shelving type, Peak: peaking type). EQ:LowG (Low Gain) -12 ­ +12 dB EQ:LoMidG (Low Middle Gain) -12 ­ +12 dB EQ:HiMidG (High Middle Gain) -12 ­ +12 dB EQ:HiG (High Gain) -12 ­ +12 db Adjust the gain (the amount of boost or cut) for each equalizer band. EQ:LowF (Low Frequency) 20 ­ 2, 000 Hz EQ:LMidF (Low Middle Frequency) 20 ­ 8, 000 Hz EQ:HMidF (High Middle Frequency) 20 ­ 8, 000 Hz HiF (High Frequency) 1. 4 ­ 20 kHz Adjust the center frequency of each equalizer band. [. . . ] Read this section in conjunction with the DS-90 owner's manual. Digitally connect the SRJV80-05 Ver. 2. 0 to the DS-90 (coaxial or optical. ) Set the DS-90's input select switch to the digital input that you are using. Make settings so that the mix bus is output from the digital output connector you connected in step 1. Hold down [SHIFT] and press [EDIT (FADER)]. Press PARAMETER [ ] or [ ] to let "DigitalOut1=" or "DigitalOut2=" appears in the display. Speaker Modeling (11 preset) No. C29 C30 C31 C32 C33 C34 Patch Name SPM:SuperFlt SPM:P. GenBlk SPM:P. E-Bs SPM:P. Mack SPM:SmalCube SPM:WhiteCon Type Insert Insert Insert Insert Insert Insert Input Stereo Stereo Stereo Stereo Stereo Stereo 2. 4 SRJV80-05 Newly added functions (Ver. 2. 0) No. C35 C36 C37 C38 C39 Patch Name SPM:W. C+tiss SPM:S. Radio SPM:SmallTV SPM:BoomBox SPM:BB. LowBs Type Insert Insert Insert Insert Insert Input Stereo Stereo Stereo Stereo Stereo Display FX1 Sel EFFECT C10:MTK:Mixdown If the recording mode of the song is set to "MAS", above mentioned settings for TR7 and 8 are automatically applied to TR5 and 6. Added EZ routing (Mastering) To EZ Routing (template/step edit), "Mastering" for mixdown is newly added. Press [SELECT (CH EDIT)] of the track that you wish to playback. Then press PARAMETER [ ]. fig. 5-18a 7. Adjust the pan/balance of the channel. Press the SELECT (CH EDIT) button for the input whose pan/balance you wish to adjust, and use the TIME/VALUE dial. Then press PARAMETER [ ]. fig. 5-19 8. Adjust the level of the channel. If you do not wish to send the channel to the AUX bus, select "Off, " and press PARAMETER [ ]. 20. "Change Routing ?" appears in the display. When the routing has been finalized, "Complete" appears in the display, and you will return to Play condition. If you decide to discard the routing that was set, press [NO]. Creating an Audio CD (CD-R Write) This explains how a CD-R/-RW drive connected to the SCSI connector of the SRJV80-05 ver. 2. 0 can be used to create original audio CD's, or to back up song data. Please also read "Chapter 8 Use with a CD-RW Drive" in the SRJV80-05 Owner's Manual (p. 107). fig. 05-26 Creating silence between songs (Disc at Once and Track at Once) When writing songs to a CD-R disc, you can select how the space between songs will be handled. Disc at Once 14-1. Use the TIME/VALUE dial to adjust the AUX send level, and press PARAMETER [ ]. Use the TIME/VALUE dial to adjust the AUX send pan, and press PARAMETER [ ]. "Master Sel=" appears in the display. Use the TIME/VALUE dial to select the bus (MIX, AUX, FX1, FX2, REC) that you wish to output from the MASTER jacks. The song data and the track number markers attached to the song data will be written to the CD-R disc without change. However, additional song data cannot be added later to a CD-R disc that was written using Disc At Once. [. . . ] Press [SONG] several times until "CD-R Recover ?" appears in the display. "STORE Current?" (Store the current song?) appears in the display. If you wish to save the current song, press [YES]; if not, then press [NO]. If you have selected a demo song, then press [NO]. [. . . ]