User manual ROLAND SSC-8004 V1.00 MIDI IMPLEMENTATION

[. . . ] Use a USB cable to connect the Fantom-G to your computer. 3 Use a USB cable to connect the Fantom-G to your computer. Use a USB cable to connect the Fantom-G to your computer. 2 Turn on the power on the Fantom-G. The message "Found New Hardware" will appear near the taskbar, and then the "Found New Hardware Wizard" will appear. If the Found New Hardware Wizard asks whether you want to connect to Windows Update, choose "No, . . . " and click [Next]. 4 Turn on the power on the Fantom-G. The message "Installing device driver software" will appear near the taskbar, and the driver will be installed automatically. If a different message appears, proceed as directed by that message. 3 Choose the installation method. [. . . ] Make sure that "Roland Fantom G" is displayed, and click [Finish]. In the "Driver Setup" dialog box, click [Close]. If the "System Settings Change" dialog box appears, click [Yes]. Restart Windows. 3 Performance Options settings 1 Open the System Properties dialog box. 2 3 In the area at left, click "Advanced system settings. " If a User Account Control screen appears, click [Continue]. If you are asked to enter the password of an Administrator account, log on to Windows as a user whose account type is Administrator, and then make the settings again. This completes the driver installation. By making these settings you may be able to prevent clicks or pops in the sound. Be sure to make the settings as described below. 3 Performance Options settings 1 Open the System Properties dialog box. If the screen indicates "Pick a category, " click [Performance and Maintenance]. In "or pick a Control Panel icon, " click the [System] icon. 2 Open the Performance Options dialog box. Click the "Advanced" tab, and in the "Performance" area, click [Settings]. 3 Enable "Background services. " 1. "Install Roland Fantom G Driver" will appear; click [Continue] as directed in the screen. When "Select a Destination" appears, select the startup disk, and click [Continue]. When "Easy Install" appears, click [Install] (or [Upgrade]). If an authentication dialog box appears, enter the password you use for Mac OS, and click [OK]. Visit us online at www. Roland. com Can't install the driver · Did you log on to Windows with the appropriate user privileges? You must log on to Windows as a user whose account type is Administrator. Can't select/use the Fantom-G device · Is the driver correctly installed? If you're unable to use the Fantom-G even though the driver was installed, it is possible that the driver was not installed correctly. Re-install the driver following the correct procedure. · Is the Fantom-G's MIDI/WAVE device name displayed? If you're using Windows and the device name is not displayed, close all applications that are using the Fantom-G, turn off the Fantom-G's power, then turn it back on again. If this does not solve the problem, install the driver once again. · Could your computer have entered Sleep or Standby (Suspend) mode while the Fantom-G was powered up and connected? If the Fantom-G does not operate correctly after your computer returns from Sleep or Standby (Suspend) mode, close all the software you're using, and then turn the Fantom-G's power off, then on again. 4. When "Installing this software requires you to restart ~" appears, click [Continue Installation]. When you see "The software was successfully installed, " click [Restart] to restart your Mac. This completes the driver installation. · While using the Fantom-G, could you have disconnected and reconnected the USB cable or switched the Fantom-G's power off, then on again? If you disconnect and reconnect the USB cable or cycle the power to the Fantom-G during use, it may stop operating correctly. In this case, close all the software you're using, and then turn the Fantom-G's power off, then on again. 2 Connecting the Fantom-G to your Mac 1 Use a USB cable to connect the Fantom-G to your Mac. Turn OFF the Fantom-G's POWER switch. Use a USB cable to connect the Fantom-G to your Mac. Connect the cable to a USB connector on the Mac itself (not to the USB connector on your keyboard). · On some computers, if Windows is started up when the Fantom-G is already connected, the driver might not be loaded correctly, making it impossible to use the Fantom G via USB. In this case, turn on the Fantom-G's power after Windows has started up, or connect it after Windows has started up. A number such as "2-" is now displayed at the beginning of the device name · Could you have connected the Fantom-G to a different USB port? If you connect the Fantom-G to a different USB port, the operating system may automatically add a number to the beginning of the device name. [. . . ] Input tab "Choose a device for sound input" This completes the audio input/output settings. The Fantom-G Editor CD-ROM contains "Fantom-G Editor, " which lets you edit the Fantom-G from your computer puter, and "Fantom-G Librarian, " which lets you manage various data on your computer. "Fantom G Librarian " computer Fantom-G Editor Fantom-G Editor is software that lets you edit the Fantom-G's parameters from your computer. In addition to editing Studio Sets and Live Sets, you can edit the Patches, Rhythm Sets, and Sample Sets used in these sets. [. . . ]