User manual ROLAND TD-4K2 SETUP GUIDE

[. . . ] Place directly below the hi-hat. If the stand wobbles, loosen this hand knob and adjust the height. Pad mounts Align with indentation Use Drum Key Use Drum Key to tighten to tighten FD-8 While pressing Position things so the striking surface of the kick drum is approximately 10­12 cm in front of the pipe. Use Drum Key Assemble the hi-hat control pedal (FD-8) * For reasons of safety, do not spread the stand wider than 1. 0 meters (40 inches). Attach the anchor bolt (if installing on a drum mat) Anchor bolt Spring for the anchor bolt to tighten Attach the kick pedal (KD-9) Adjusting the pedal depth Loosen with the drum key, and tighten after adjusting Deeper Slide the arm Shallower Attach the snare (PDX-8) and toms (PD-8) Tighten Tighten Anchor bolt Loosen Install the kick pedal securely. Rod Loosen Rod 1. 0 m 04 Connect the pads to the sound module RD As seen from the front CR1 * Use cable ties to fasten the cables at the circled locations " " so that they do not interfere with your performance. Make sure to wrap the cable ties around the pipes. 05 Power cord Connect the AC adaptor and speakers * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn o the power on all devices before making any connections. Connection procedure * Insert the plug firmly, making sure it's all the way in. T2 T3 TD-4 T1 SNR HH AC adaptor Stereo 1/4" plug Stereo Headphones Knob 1. [. . . ] * The TD-4 percussion sound module supports rim shots only for the snare. It does not support rim shots for toms. PDX-8 (Snare) PDX-8 component names Tuning bolts Hoop Rim rubber Head sensor Head Wing nut OUTPUT jack Shell Adjusting the tension PDX-8 NOTE * Be sure to adjust the head tension of the PDX-8 before use. * Striking the head when the head tension is loose may damage the sensor and head. * Do not apply excessive force to the sensor and cushion located under the head. Doing so can interfere with accurate detection, and may damage it. * Due to the nature of the materials used in the sensor of the PDX-8, changes in room temperature may affect the sensitivity of the sensor. 4 2 5 6 1 3 2 5 Head replacement procedure PDX-6 4 1 3 The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: Slack portions remain in the head even when the head tension is properly adjusted. * To obtain replacement heads, please contact the nearest Roland Service Center or an authorized Roland distributor, as listed in "Information. " 1. Finger-tighten all of the tuning bolts in the sequence shown in the illustration. The appropriate amount of tension is one that will provide approximately the same striking response as on an acoustic drum. Use the drum key to adjust the tension as needed. Loosen Tighten Drum key 1. Remove all tuning bolts and washers. * Do not apply excessive force to the sensor and cushion located under the head. Doing so can interfere with accurate detection, and may damage it. Tuning bolts 2. Attach the tuning bolts to the hoop and shell. Adjust the head tension. Holder Rim sensor * The rim rubber is one component that eventually wears out (depending on the number and strength of the rim shots performed), and will require replacement. Rim shots may not be performed correctly when the rim rubber is worn out. Consult Roland Service for more on replacing the rim rubber. Hoop Head Rim rubber Head sensor Rim sensor Suitable position for rim shots Player Shell IMPORTANT NOTES About WARNING and CAUTION Notices About the Symbols The symbol alerts the user to important instructions or warnings. The speci c meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The speci c thing that must not be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the unit must never be disassembled. The symbol alerts the user to things that must be carried out. The speci c thing that must be done is indicated by the design contained within the circle. In the case of the symbol at left, it means that the power-cord plug must be unplugged from the outlet. For EU Countries Placement · Do not expose the unit to direct sunlight, place it near devices that radiate heat, leave it inside an enclosed vehicle, or otherwise subject it to temperature extremes. [. . . ] · Never use benzine, thinners, alcohol or solvents of any kind, to avoid the possibility of discoloration and/ or deformation. juice) to enter this product. Doing so may cause short circuits, faulty operation, or other malfunctions. · In households with small children, an adult should provide supervision until the child is capable of following all the rules essential for the safe operation of the unit. · Protect the unit from strong impact. [. . . ]