User manual ROLAND TD-6V V1.00 MIDI IMPLEMENTATION

[. . . ] MIDI Implementation Model TD-6V Version 1. 00 Oct. 24, 2003 Foot Control (Controller number 4) Status BnH 2nd byte 04H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Normal mode Section 1. Receive data Channel Voice Messages * Following Channel Voice Messages can be recorded in SETUP/MIDI PART/ Part CH. n = MIDI channel number: vv = Control value: * * Only the channel assigned to the drum kit part can be received. When recording, this will be recorded as PEDAL CC data in the sequencer data itself. Data Entry (Controller number 6) Status BnH 2nd byte 06H 3rd byte mmH Note Off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) mm = The value of the parameter specified by RPN. [. . . ] : Data Checksum EOX (End Of Exclusive) n = MIDI channel number: vv = Modulation depth: * In the rhythm part (ch. 10), ignored this message. Data Entry (Controller number 6, 38) Status BnH BnH 2nd byte 06H 26H 3rd byte mmH llH n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) mm, ll = The value of the parameter specified by RPN. mm = upper byte (MSB), ll = lower byte (LSB) * In the rhythm part (ch. 10), ignored this message. On the GM mode of TD-6V, RPN can be used to modify the following parameters. RPN MSB LSB 00H 00H Data entry MSB LSB mmH --- * * The amount of data that can be transmitted at once time will depend on the type of data, and data must be requested using a specific starting address and size. Refer to the Address and Size listed in "Parameter address map" (page 9). Data larger than 128 bytes must be divided into packets of 128 bytes or less. If "Data Set 1" is transmitted successively, there must be an interval of at least 40 ms between packets. Regarding the checksum please refer to page 12. 00H 01H mmH llH 00H 02H mmH --- 7FH 7FH --- --- GM mode Section 1. Receive data Channel Voice Messages * The following Channel Voice messages can be received on channels for which the SETUP/GM PART/Part Rx Sw is set to "ON". Status BnH 2nd byte 07H Explanation Pitch Bend Sensitivity mm:00H - 18H (0 - 24 semitones) ll: ignored (processed as 00H) specify up to 2 octaves in semitone steps Channel Fine Tuning mm, ll: 00 00H - 40 00H - 7F 7FH (-100 - 0 - +99. 99 cents) Refer to "About tuning" (page 13). Channel Coarse Tuning mm: 28H-40H-58H (-24 - 0 - +24 semitones) ll: ignored (processed as 00H) RPN null set condition where RPN is unspecified. The data entry messages after set RPN null will be ignored. (No Data entry messages are required after RPN null). mm, ll: ignored Volume (Controller number 7) 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) Note Off Status 8nH 9nH 2nd byte kkH kkH 3rd byte vvH 00H 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) n = MIDI channel number: vv = Volume: * Volume messages are used to adjust the volume balance of each part. n = MIDI channel number: kk = note number: vv = note off velocity: * * Pan (Controller number 10) Status BnH 2nd byte 0AH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 40H - 7FH (Left - Center - Right) In the rhythm part (ch. 10), ignored this message. The Velocity Values of Note Off message are ignored. n = MIDI channel number: vv = pan: * Note On Status 9nH 2nd byte kkH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 00H - 7FH (0 - 127) In the rhythm part (ch. 10), ignored this message. Expression (Controller number 11) Status BnH 2nd byte 0BH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) n = MIDI channel number: kk = note number: vv = note on velocity: n = MIDI channel number: vv = Expression: * Expression messages are used to adjust the level of each part. It can be used independently from volume messages. Expression messages are used for musical expression within a performance; e. g. , crescendo and decrescendo. 6 MIDI Implementation Hold 1 (Controller number 64) Status BnH 2nd byte 40H 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) 0-63 = OFF, 64-127 = ON Channel Mode Messages All Sounds Off (Controller number 120) Status BnH 2nd byte 78H 3rd byte 00H 0H - FH (ch. 1 - ch. 16) n = MIDI channel number: vv = Control value: * In the rhythm part (ch. 10), ignored this message. n = MIDI channel number: * Effect 1(Reverb Send Level) (Controller number 91) Status BnH 2nd byte 5BH 3rd byte vvH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (0 - 127) When this message is received, all currently-sounding notes on the corresponding channel will be silenced. However, the status of channel messages will not change. n = MIDI channel number: vv = Reverb send level: Reset All Controllers (Controller number 121) Status BnH 2nd byte 79H 3rd byte 00H 0H - FH (ch. 1 - ch. 16) RPN MSB/LSB (Controller number 100, 101) Status BnH BnH 2nd byte 65H 64H 3rd byte mmH llH n = MIDI channel number: * When this message is received, the following controllers will be set to their reset values. Reset value +/-0 (center) 0 (off) 0 (off) 127 (max) 0 (off) unset; previously set data will not change n = MIDI channel number: 0H - FH (ch. 1 - ch. 16) mm = upper byte of parameter number specified by RPN (MSB) ll = lower byte of parameter number specified by RPN (LSB) * * * In the rhythm part (ch. 10), ignored this message. The value specified by RPN will not be reset even by messages such as program change or reset all controllers. Regarding the RPN please refer to page 2. Controller Pitch Bend Change Channel Key Pressure Modulation Expression Hold 1 RPN On the GM mode of TD-6V, RPN can be used to modify the following parameters. Regarding the value of each parameter, refer to Data Entry (Controller number 6, 38). RPN mm 00H 00H 00H 7FH All Notes Off (Controller number 123) Status BnH 2nd byte 7BH 3rd byte 00H 0H - FH (ch. 1 - ch. 16) n = MIDI channel number: ll 00H 01H 02H 7FH Parameter Pitch Bend Sensitivity Channel Fine Tuning Channel Coarse Tuning RPN null * When All Notes Off is received, all notes on the corresponding channel will be turned off. However if Hold 1 is ON, the sound will be continued until these are turned off. System Realtime Message Active Sensing Status FEH Program Change Status CnH 2nd byte ppH 0H - FH (ch. 1 - ch. 16) 00H - 7FH (prog. 1 - prog. 128) n = MIDI channel number: pp = Program number: * * The sound will change beginning with the next note-on after the program change is received. [. . . ] It is not desirable for performance data (such as Standard MIDI File data) to contain many events with running status as given in. This is because if playback is halted during the song and then rewound or fast-forwarded, the sequencer may not be able to transmit the correct status, and the sound source will then misinterpret the data. Take care to give each event its own status. It is also necessary that the RPN or NRPN parameter number setting and the value setting be done in the proper order. [. . . ]