User manual ROLAND TD-7K

[. . . ] The manual should be saved and kept on hand as a convenient reference. * Kick Pedal and Hi-Hat stand are not included. 202 Copyright © 2005 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. USING THE UNIT SAFELY Used for instructions intended to alert the user to the risk of death or severe injury should the unit be used improperly. Used for instructions intended to alert the user to the risk of injury or material damage should the unit be used improperly. * Material damage refers other adverse effects respect to the home furnishings, as well animals or pets. [. . . ] * Set the KD-85 so no mechanical noise is heard when you step on pedal. * Make sure that KD-85 does not touch the drum stand or the other pads. 7 IMPORTANT NOTES To Obtain More Stability If you are using a kick pedal with an under plate Adjust the length of the legs and the angle of the stay so that the four legs of the KD-85 and the heel of the kick pedal contact the floor evenly. Replacing the Head When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: · The head surface is torn · Slack portions remain in the head even when the head tension is properly adjusted. Replacement heads (optional): MH-8 Mesh Head 13. Adjust the striking point for the beater. The beater's striking point is adjusted to fall at the center of the head. Adjust the striking point so that it doesn't extend beyond the cushion on the back of the head. 1. Remove all tuning bolts and washers from the KD-85. Press the lock bushing (in figure below) in place with your finger as you remove each tuning bolt, to prevent the bushings from being pulled off the frame. fig. Replace. e When Using a Twin (Double Kick) Pedal With the KD-85, you can also play using a twin (double kick) pedal. Set this up so the striking points of the two beaters fall at equal distances to the left and right of the center of the head. Lock Bushing Washer Loosen Tighten Tuning Key When using a twin (double kick) pedal, as with a regular pedal, use the included beater or a plastic beater as the beater for the kick pedal. fig. Twin Frame Hoop Tuning Bolt * The lock bushings prevent rotation and loosening of the tuning bolts caused by vibrations that are transmitted from the hoop as you play. 3. Pass the tuning bolts through the washers, then attach them to the hoop and frame. Next, adjust the tension of the head (p. 6). * Do not firmly tighten a single tuning bolt by itself. If it remains loose, the pad could fall off. * The lock bushings prevent rotation and loosening of the tuning bolts caused by vibrations that are transmitted from the hoop as you play. 2. Remove the old head. Replacing the Head When the Head Should Be Replaced The head is an expendable item that eventually will wear out and need to be replaced. Replace the head when the following occurs: · The head surface is torn · Striking points are no longer detected correctly, even when the head tension is properly adjusted. · Slack portions remain in the head even after the head tension is properly adjusted. Replacement heads (optional): MH-8 Mesh Head 4. Pass the tuning bolts through the washers, then attach them to the hoop and frame. Next, adjust the tension of the head (p. 10). If a lock bushing happens to become separated from the frame while the head is being replaced, position the bushing so its four slots are aligned with the corresponding ridges in the frame, then press down firmly on the bushing. fig. LockBush. e Lock Bushing Frame 11 IMPORTANT NOTES CY-12R/C (V-Cymbal Ride/Crash) Bell Attaching the V-Cymbal to the Cymbal Mount 1. Remove the wing nut, felt, collar, and washer included with the cymbal mount. Use the tuning key supplied with the VH-11 to tighten the stopper bolt. The stopper keeps the CY-12R/C from turning, and prevents the cables from catching or getting tangle on the stand. Bow Edge BOW/EDGE Output Jack Stopper (Be sure to orient it correctly) Tighten the bolt with a tuning key BOW/BELL Output Jack 3. Attach the CY-12R/C so the unit is oriented as shown in the diagram (bolt should be opposite the output jacks). Wing Nut Wing Nut Felt Washer Felt Washer Stopper 4. [. . . ] MEXICO TEL: (55) 5668-6699 TURKEY ZUHAL DIS TICARET A. S. No. 37 Beyoglu - Istanbul / TURKEY TEL: (0212) 249 85 10 FINLAND Roland Scandinavia As, Filial Finland Elannontie 5 FIN-01510 Vantaa, FINLAND TEL: (0)9 68 24 020 BARBADOS A&B Music Supplies LTD 12 Webster Industrial Park Wildey, St. Michael, Barbados TEL: (246)430-1100 UKRAINE EURHYTHMICS Ltd. 30 UA - 89600 Mukachevo, UKRAINE TEL: (03131) 414-40 U. A. E. Zak Electronics & Musical Instruments Co. TEL: (04) 3360715 NICARAGUA Bansbach Instrumentos Musicales Nicaragua Altamira D'Este Calle Principal de la Farmacia 5ta. Avenida 1 Cuadra al Lago. #503 Managua, Nicaragua TEL: (505)277-2557 GERMANY Roland Elektronische Musikinstrumente HmbH. [. . . ]