User manual ROLAND V-PRODUCER SCREEN REFERENCE

[. . . ] Screen reference This chapter provides screen-by-screen explanations of all the functions available in VProducer. V-Producer screen fig. 01-all A E b' d F C D B b g G A. 29) The locator contains functions for controlling the playback of V-Producer, such as song play/ stop. 3) Sample List displays a list of the samples that are loaded into the VariOS. To load a sample into the VariOS, press the [b'] (Load Wave Files) button (p. [. . . ] There are 40 different multi-effects, 8 kinds of chorus, and 9 kinds of reverb. One of each can be used, and you can adjust the depth of each effect for each part. Effect settings can be broadly divided into the following two types: 1. The on/off settings made directly in the sound generator (User Guide) 2. The settings made in the Mixer window of V-Producer (p. 53) Effect structure and output jacks You can specify how deeply each effect will be applied, and the output jack from which its sound will be sent. Some parameters are set for each part, and other parameters are set for all parts in common. * For actual examples of using the mixer, refer to VariOS Mixer (p. The following diagram shows the signal flow. fig. newmixer Reverb Send Level Reverb Master Level Reverb Chorus Send Level Chorus Rev Send Level MAIN OUT Chorus OUTPUT Sound Generator Chorus Master Level MAIN M-FX DIR Multi-FX Send Level Multi-FX Cho Send Level DIGITAL OUT Multi-FX Rev Send Level Multi-FX Master Level Multi-FX Out Assign Multi-FX DIRECT OUT * The same sound as output from the "MAIN OUT" OUTPUT jacks will be output from the two digital output connectors and the PHONES jack. This means that if you wish to output the effect sound from the two digital output connectors and the PHONES jack, you should specify that the effect sound be output from "MAIN OUT. " 109 The effects of the sound generator section Parameter Values OUTPUT MAIN, M-FX, DIR MFX Send Level 0-127 Chorus Send Level 0-127 Reverb Send Level 0-127 Multi-FX Out Assign (Multi-effect output assign) Multi-FX Cho Send Level (Multi-effect chorus send level) Multi-FX Rev Send Level (Multi-FX reverb send level) Chorus Rev Send Level (Chorus reverb send level) MFX Master Level (Multi-FX master level) Chorus Master Level Reverb Master Level MAIN, DIR 0-127 0-127 0-127 0-127 0-127 0-127 Description This specifies the output destination of the direct sound. MAIN: The sound will be output to reverb, chorus, and the "MAIN OUT" OUTPUT jacks. Select this setting when you wish to use reverb and chorus, but not multi-effects. M-FX: The sound will be output to reverb, chorus and multi-effects. Select this setting when you wish to use reverb, chorus, and multi-effects. DIR: Output is from the "DIRECT OUT" OUTPUT jacks. Use this setting when you want to use an external effects processor, not the VariOS's build-in effects. Specifies the multi-effects depth. Sets the extent of the effectiveness of the multi-effects. * If Output Assign is set to "M-FX, " this setting will be applied. * If Output Assign is set to "DIR1" or "DIR2, " this setting will be ignored. * If Output Assign is set to "DIR1" or "DIR2, " this setting will be ignored. Specifies how the sound from the multi-effects will be output. MAIN: Output is from the "MAIN OUT" OUTPUT jacks. [. . . ] remainder 128 - remainder = checksum <Example 1> Setting the Performance Common REVERB TYPE to HALL 1 (DT1) The "Parameter address map" indicates that the starting address of the Performance is 10 00 00 00H, that the Performance Common offset address is 00 00H, and that the REVERB TYPE address is 00 32H. Thus, the address is: 10 00 00 00 00 10 00 00 00H 00H 32H 32H +) Since HALL 1 is parameter value 03H, F0 (1) 41 (2) 10 (3) 00 (4) 1D (5) 12 (6) 10 00 00 32 address 03 size ??checksum F7 (7) (1) Exclusive status (3) Device ID (17) (5) Model ID#2 (VariOS) (2) ID number (Roland) (4) Model ID#1 (VariOS) (6) Command ID (DT1) (7) EOX Next we calculate the checksum. 10H + 00H + 00H + 32H + 03H = 16 + 0 + 0 + 50 + 3 = 69 (sum) 69 (total) / 128 = 0 (quotient) . . . [. . . ]