User manual ROLAND V-STUDIO 100

[. . . ] Hardware Manual USING THE UNIT SAFELY About WARNING and CAUTION Notices About the Symbols The symbol alerts the user to important instructions or warnings. The specific meaning of the symbol is determined by the design contained within the triangle. In the case of the symbol at left, it is used for general cautions, warnings, or alerts to danger. The symbol alerts the user to items that must never be carried out (are forbidden). The specific thing that must not be done is indicated by the design contained within the circle. [. . . ] When the file has been deleted, you will return to the finder screen. Press the [DISPLAY] button to return to the previous screen. 36 Connections 37 Connections Connecting the AC adaptor Connect the included AC adaptor to the SONAR V-STUDIO 100's DC IN jack. fig. Connect-ACadpt. eps Power Cord (included) AC Adaptor (included) DC IN to Power Outlet Indicator Place the AC adaptor so the side with the indicator (see illustration) faces upwards and the side with textual information faces downwards. * The indicator will light when you plug the AC adaptor into an AC outlet. To prevent the inadvertent disruption of power to your unit (should the plug be pulled out accidentally), and to avoid applying undue stress to the AC adaptor jack, anchor the power cord using the cord hook, as shown in the illustration. fig. CordHook. j. eps Cord Hook AC Adaptor Cord 38 Connections Connecting computers and audio equipments Before connecting the SONAR V-STUDIO 100 to a computer, read the separate Installation Guide and install the SONAR V-STUDIO 100 driver on the computer. If the driver is not installed, SONAR V-STUDIO 100 cannot be operated correctly from the computer. · Use a USB cable to connect your computer to the SONAR V-STUDIO 100. · Connect your audio output devices such as headphones or speakers to the SONAR V-STUDIO 100. * This package does not include audio output devices such as headphones or speakers. fig. Connect-basic. eps Monitor amplified speakers Headphones USB Connector Computer 39 Turning the power on * Once the connections have been completed (p. 38), turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. * This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. * Always make sure to have the volume level turned down before switching on power. Even with the volume all the way down, you may still hear some sound when the power is switched on, but this is normal, and does not indicate a malfunction. 1. Turn the SONAR V-STUDIO 100's [MAIN MIX] knob and the Headphone [VOLUME] knob to the minimum. fig. Vol-Min. eps 2. If the SONAR V-STUDIO 100 is connected to a computer, turn on the power of your computer. Turn on the power switch of SONAR V-STUDIO 100. fig. P-ON. eps 4. Turn on the power of the monitor speaker. * To protect its circuits, the SONAR V-STUDIO 100 does not operate for a while after you turn the power on. 40 Connections and signal flow Connecting microphones and guitars fig. Connect-mic-guitar. eps Guitar/Bass Microphone Connect the guitar or bass to INPUT 1 If you use a phantom power-enable condencer microphone, set this switch to "+48V" Adjust the input level Hi-Z Adjust the input level * To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. * When connection cables with resistors are used, the volume level of equipment connected to the INPUT connectors may be low. If this happens, use connection cables that do not contain resistors. * Feedback could be produced depending on the location of microphones relative to speakers. Changing the orientation of the microphone(s). Relocating microphone(s) at a greater distance from speakers. * Do NOT connect anything to input terminals that you are not using. Adjusting the level Use the [SENS] knob to adjust the input level. To achieve the best recording quality, display the level meter on the screen and use the [SENS] knob to increase the level as far as possible without the input level exceeding the normal level. 41 Connections and signal flow Signal flow when recording with SONAR fig. routing01. eps To USB WAVE IN 1-2 WAVE OUT 1-2 WAVE IN MAIN [SENS] 1L INPUT 2R [LEVEL] [PAN] [PLAYBACK] MAIN OUTPUT 1/2 [MAIN MIX] [VOLUME] MIXER PHONES output If you connect the SONAR V-STUDIO 100 to your computer with a USB cable, you can use SONAR to record sounds input to INPUT 1L/INPUT 2R. [. . . ] TEL: +44 (0)20 8747 5949 FAX:+44 (0)20 8747 5948 http://www. edirol. com/europe Deutschland TEL: 0700 33 47 65 20 Italia TEL: 02 93778329 TAIWAN ROLAND TAIWAN ENTERPRISE CO. , LTD. 112 Chung Shan N. Road Sec. 2, Taipei, TAIWAN, R. O. C. TEL: (02) 2561 3339 CZECH REP. CZECH REPUBLIC DISTRIBUTOR s. r. o Voctárova 247/16 CZ - 180 00 PRAHA 8, CZECH REP. TEL: (2) 830 20270 VIET NAM VIET THUONG CORPORATION 386 CACH MANG THANG TAM ST. [. . . ]