User manual ROLAND V-STUDIO 700

[. . . ] Owner`s Manual Read this First This manual provides instructions on how to use the VS-700R I/O on its own and how to add on a second VS-700R I/O. For instructions on how to perform the installation, make the necessary settings, and operate the unit, please refer to the "VS-700 Getting Started" and the "VS-700 Owner's Manual. " WARNING: To reduce the risk of fire or electric shock, do not expose this apparatus to rain or moisture. CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN ATTENTION: RISQUE DE CHOC ELECTRIQUE NE PAS OUVRIR CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with arrowhead symbol, within an equilateral triangle, is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons. The exclamation point within an equilateral triangle is intended to alert the user to the presence of important operating and maintenance (servicing) instructions in the literature accompanying the product. INSTRUCTIONS PERTAINING TO A RISK OF FIRE, ELECTRIC SHOCK, OR INJURY TO PERSONS. IMPORTANT SAFETY INSTRUCTIONS SAVE THESE INSTRUCTIONS WARNING - When using electric products, basic precautions should always be followed, including the following: 1. [. . . ] Connect the second VS-700R I/O unit to your computer's USB connector. 12 Connecting Two VS-700R I/O Units 3. Connect the WORDCLOCK. Use a BNC cable to connect the WORDCLOCK OUT connector of the first unit to the WORDCLOCK IN connector of the second unit. Set the audio clock source of the second unit to "Wordclock" (p. Now the audio clock of the second unit will be synchronized. * A BNC cable is not included with this package. 4. Start up SONAR. The USB connectors to which you connect the two VS-700R I/O units must share the same USB controller within your computer. Otherwise, the audio ports of the second unit won't be recognized. If the audio ports of the second VS-700R I/O unit are not displayed in SONAR, try reconnecting the USB cables of the two VS-700R I/O units to different connectors on your computer, then quit and restart SONAR. Repeat this procedure until the audio ports of both VS-700R I/O units are displayed. Alternatively, you can connect the two VS-700R I/O units to a USB hub that is compatible with USB 2. 0, and connect the hub to your computer. Regarding Monitoring By connecting the direct monitor mixer output of the second VS-700R I/O unit to the first VS-700R I/O unit, all inputs of the second I/O unit can be monitored from the first VS-700R I/O unit. Example connections for monitoring 1. Connect the second unit's SUB OUT to the first unit's INPUT 7/8. As the second unit's direct monitor mixer output, select SUB. On the first unit, adjust the INPUT 7/8 input level. You'll hear the second unit's direct monitor signal in the first unit's direct monitor mixer output. 13 Connecting the Power Cord · Connect the power cord. fig. VS-700-connect04-e. eps VS-700C Rear Panel to Power Outlet Power Cord VS-700R Rear Panel Power Cord to Power Outlet 14 Turning the Power On 941 Once the connections have been completed, turn on power to your various devices in the order specified. By turning on devices in the wrong order, you risk causing malfunction and/or damage to speakers and other devices. 945 If you need to turn off the power completely, first turn off the POWER switch, then unplug the power cord from the power outlet. Minimize the VS-700C's [AUDIO OUTPUT] knobs (three locations). VS-700C Top Panel 2. Turn on the power switch of the VS-700C. VS-700C Rear Panel Power On 4. Turn on the power switch of two VS-700R. VS-700R Front Panel Power On 5. Turn on the power switch of your monitor speakers. 942 Due to a circuitry-protection feature, the VS-700R requires a few moments after power-up before it is ready for normal operation. If the connections are correct, the VS-700R's USB indicator will light. If the USB indicator of the VS-700R I/O unit isn't lit If the USB indicator of the VS-700R isn't lit, the driver has not been installed correctly. Refer to the "Troubleshooting" chapter in "Getting Started. " If the I/O indicator of the VS-700C console or the CONSOLE indicator of the VS-700R I/O unit is blinking Check the following points. · Are the VS-700C and VS-700R powered up?· Are the VS-700C and VS-700R correctly connected via the dedicated cable? [. . . ] Fixer le couvercle en inversant l'etape 2 du processus d'installation. 28 Attaching the Rackmount Brackets If you want to install the VS-700R I/O in a 19" rack, attach the included rackmount brackets. 1. Disconnect all connection cables from the VS-700R, including the power cord. As shown in the illustration below, remove three screws each from the left and right sides of the VS-700R. fig. rack01. eps 3. Attach the rackmount brackets using the screws you removed in step 2. fig. rack02. eps 4. [. . . ]