User manual ROLAND VARIOS-8

[. . . ] Introduction VariOS-8 is a trial application that transforms your VariOS into a completely different sound module. When the VariOS-8 program is installed, you can use the VariOS as an analog modeling synthesizer. You can use a rich array of parameters to produce realistic analog synthesizer sounds. Copyright © 2003 ROLAND CORPORATION All rights reserved. No part of this publication may be reproduced in any form without the written permission of ROLAND CORPORATION. [. . . ] Adjusts the pitch LFO depth for OSC1/2. 16 Screen reference OSC1/2 screen 1 1. OSC LFO1/2 Parameter RATE DELAY FADE IN WAVEFORM Value 0­127 0­127 0­127 SINE, TRI, SAW, SQR, RND, TAP, S&H, CHAOS OFF, ON -63­+63 -63­+63 -63­+63 -63­+63 2 2 3 KEY SYNC PITCH DEPTH PW DEPTH SUB OSC DEPTH LEVEL DEPTH Description Adjusts the modulation rate, or speed, of the LFO. Delay Time (LFO Delay Time) specifies the time elapsed before the LFO effect is applied (the effect continues) after the key is pressed (or released). Specifies the time over which the LFO amplitude will reach the maximum. SINE: Sine wave TRI: Triangle wave SAW: Sawtooth wave SQR: Square wave RND: Random wave TAP: Trapezoidal wave S&H: Sample & Hold wave (one time per cycle, LFO value is changed) CHAOS: Chaos wave This specifies whether the LFO cycle will be synchronized to begin when the key is pressed (ON) or not (OFF). Specifies how deeply the LFO will affect pulse width. Specifies how deeply the LFO will affect SUB OSC. Specifies how deeply the LFO will affect the volume of the oscillator. 2. PITCH ENV1/2, PW ENV1/2 Parameter DEPTH A D S R Value -63­+63 0­127 0­127 0­127 0­127 Description Specifies the depth of the envelope. Higher settings will cause the envelope to produce greater change. Negative (-) settings will invert the shape of the envelope. Specifies the attack time of the envelope (the time from when you press a key until the envelope level reaches the maximum value). Specifies the decay time of the envelope (the time from when the envelope level reaches the maximum value until it falls to a constant value). Specifies the sustain level of the envelope (the level at which the envelope remains constant). Specifies the release time of the envelope (the time from when you release a key until the envelope level reaches 0). 3. TVA ENV1/2 Parameter A D S R Value 0­127 0­127 0­127 0­127 Description Specifies the attack time of the envelope (the time from when you press a key until the envelope level reaches the maximum value). Specifies the decay time of the envelope (the time from when the envelope level reaches the maximum value until it falls to a constant value). Specifies the sustain level of the envelope (the level at which the envelope remains constant). Specifies the release time of the envelope (the time from when you release a key until the envelope level reaches 0). 17 Screen reference TVF screen 1 1. TVF LFO Parameter RATE DELAY FADE IN WAVEFORM Value 0­127 0­127 0­127 SINE, TRI, SAW, SQR, RND, TAP, S&H, CHAOS OFF, ON -63­+63 -63­+63 2 2 KEY SYNC FREQ DEPTH RESO DEPTH Description Adjusts the modulation rate, or speed, of the LFO. Delay Time (LFO Delay Time) specifies the time elapsed before the LFO effect is applied (the effect continues) after the key is pressed (or released). Specifies the time over which the LFO amplitude will reach the maximum. [. . . ] Start up your computer, and insert the PC card into the PC card reader. From the VariOS Program folder, drag VPD-01 for VariOS. BIN to copy it into the PC card drive. Rename the copied file VPD-01 for VariOS. BIN as follows. (Change the third character from "D" to "I" (the uppercase letter "I"; not the numeral "one"). [. . . ]