User manual ROLAND VM-7100 MANUAL 2

[. . . ] OWNER'S MANUAL Thank you, and congratulations on your choice of the Roland VM-7200 (VM-7100) V-Mixing Processor. Before using this unit, carefully read the sections entitled: "IMPORTANT SAFETY INSTRUCTIONS" (p. 2), "USING THE UNIT SAFELY" (p. These sections provide important information concerning the proper operation of the unit. Additionally, in order to feel assured that you have gained a good grasp of every feature provided by your new unit, Owner's Manual should be read in its entirety. [. . . ] By connecting a Roland DIF-AT, you can exchange 8-in/8-out 24-bit digital audio signals with a digital multitrack recorder, such as the ALESIS adat or the TASCAM DA-88 (maximum of three recorders). To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. s Connecting the ALESIS adat fig. 5-08e adat DIF-AT SYNC (IN or OUT) adat Optical IN/OUT R-BUS(RMDB2) Processor (VM-7200) 1 2 Use the R-BUS cable included with the DIF-AT to connect the DIF-AT and the processor. Use an optical cable (sold separately) for use with adat to connect the adat and the DIF-AT. Make the settings for the console (master or slave) according to the connections used. Refer to the console Owner's Manual and DIF-AT Owner's Manual. Connecting to the adat's SYNC IN connector the adat in Sync Slave mode. This setup enables the transport controls to be operated from the console. Connecting to the adat's SYNC OUT connector the adat in Sync Master mode. In this setup, the transport controls cannot be operated from the console. 3 Press the Mixing Processor (VM-7200, VM-7100) POWER switch to turn on the power. Confirm that the DIF-AT's POWER indicator is lit. 30 Various Connection Setups s Connecting the TASCAM DA Series fig. 5-09e DIGITAL I/O TDIF-1 REMOTE IN / SYNC IN DIF-AT TASCAM DA series R-BUS(RMDB2) Processor (VM-7200) 1 2 3 Use the R-BUS cable included with the DIF-AT to connect the DIF-AT and the processor. Use a cable for use with TASCAM devices (sold separately) to connect the TASCAM DA Series and the DIF-AT. Press the Mixing Processor (VM-7200, VM-7100) POWER switch to turn on the power. Confirm that the DIF-AT's POWER indicator is lit. 31 Various Connection Setups Various Connection Setups Connecting Two Processors (Cascade Connection) Roland also offers the VM-24C Cascade Kit, available for separate purchase. Once the VM-24C is installed, you will be able to use the CASCADE connector (p. By cascading two VM-7000 series units, a maximum of 94 input channels can be supported (when the VM-24E and DIF-AT are used). Roland recommends that you install a VM-24C. The VM-24C includes two boards, a MASTER and a SLAVE. Install the MASTER board in one of the processors and the SLAVE board in the other processor (p. The CASCADE connectors cannot be used unless both boards are installed. fig. 5-10e Processor (SLAVE) Processor (MASTER) To prevent malfunction and/or damage to speakers or other devices, always turn down the volume, and turn off the power on all devices before making any connections. R-BUS(RMDB2) VM-LINK Console 1 Console 2 32 Various Connection Setups 1 2 Use the R-BUS cable included with the VM-24C to connect the two processors. Use the VM-LINK cable included with the console to connect the master processor and the consoles. Be careful not to connect VM-LINK cable to the slave processor. In console Owner's Manual, the master processor is called the 1st UNIT and the slave processor is called the 2nd UNIT. Turn the POWER switch on each processor to ON. [. . . ] Box 180 295400 Munkachevo, UKRAINE TEL: (03131) 414-40 FINLAND Roland Scandinavia As, Filial Finland Lauttasaarentie 54 B Fin-00201 Helsinki, FINLAND TEL: (9) 682 4020 INDIA Rivera Digitec (India) Pvt. Ltd. 409, Nirman Kendra Mahalaxmi Flats Compound Off. Edwin Moses Road, Mumbai-400011, INDIA TEL: (022) 498 3079 CENTRAL/LATIN AMERICA ARGENTINA Instrumentos Musicales S. A. Florida 656 2nd Floor Office Number 206A Buenos Aires ARGENTINA, CP1005 TEL: (54-11) 4- 393-6057 UNITED KINGDOM Roland (U. K. ) Ltd. Atlantic Close, Swansea Enterprise Park SWANSEA SA7 9FJ, UNITED KINGDOM TEL: (01792) 700139 NORTH AMERICA CANADA Roland Canada Music Ltd. (Head Office) 5480 Parkwood Way Richmond B. [. . . ]