User manual ROLAND XV-3080 QUICK START

[. . . ] Introduction Thank you for purchasing the Roland XV-3080 synthesizer module. To feel assured that you understand and can use all of the XV-3080's superior features, be sure to read the Owner's Manual in its entirety. The guide comprises two sections, a "Quick Start" manual and an "Owner's Manual. " The "Quick Start" manual (this volume) explains the XV-3080's basic functions using examples that are clear and easy to grasp. In addition to the XV-3080's basic operations, the "Owner's Manual" provides descriptions of more advanced uses and applications. [. . . ] q Quand la carte est installée, vérifiez si l'installation est correcte. Pour installer une carte d'extension (vendue en option dans les séries SRJV80 et SRX), détacher la plaque du dessus. La carte de série SRX s'installe dans l'emplacement EXP-E, F et la carte de série SR-JV80, dans l'emplacement EXP-A­D. 6 Getting Ready 1 2 Avant d'installer la carte d'extension, éteindre le XV-3080 et tous les appareils qui y sont reliés. N'enlever que les vis spécifiées sur le schéma suivant. 3 4 Enlever la plaque protectrice. Orienter le support à carte tel qu'indiqué sur le schéma. Support d'extension Wave série SRX série SR-JV80 7 Getting Ready 5 Dans l'appareil, vous trouverez des emplacements pour carte à extension de série SRX et SR-JV80. En vous référant au schéma ci-dessous, insérer le connecteur de la carte d'extension à l'emplacement correspondant tout en enfonçant simultanément le support à carte dans les trous de celle-ci. Conecteur Support d'extension Wave série SRX série SR-JV80 6 À l'aide de l'outil fourni à cet effet avec la carte, faire tourner en position "LOCK" le support à carte afin de bien la fixer. LOCK 7 Remettre la plaque à sa place et la fixer à l'aide des vis enlevées à l'étape 2. Ceci complète l'installation de la carte d'extension. 8 Getting Ready Les manipulations suivantes vous permettront de vérifier si votre carte a été correctement installée. 1 2 Allumer votre appareil en suivant les instructions de la p. 11. Appuyer sur la touche [SYSTEM]. · Are the volume levels on the XV-3080 and any amp or mixer that is connected turned down to the lowest settings? This unit is equipped with a protection circuit. A brief interval (a few seconds) after power up is required before the unit will operate normally. 2 Press the XV-3080's [POWER] switch to turn on the power. fig. 03. e 3 1 Turn on the power to connected external devices. Turning Off the Power Before turning off the power, confirm the following. · Are the volume levels on the XV-3080 and any amp or mixer that is connected turned down to the lowest settings?· Have you saved your data, including data for any sounds you have created?122) 2 3 Turn off the power to connected external devices. Press the XV-3080's [POWER] switch to turn off the power. 11 Getting Ready Restoring the Factory Settings (Factory Reset) To ensure the XV-3080 operates correctly as described in the procedures found in the Owner's Manual when using the XV-3080 for the first time, be sure to restore the settings to their initial status as shipped. fig. 04. e 1 Press the [UTILITY] button, lighting the indicator. The Utility page appears in the display. fig. 05. e 2 Press the [ fig. 06. e ]/[ ] button to select UTIL 2 page. If any important data you may have created is stored in memory, then running this operation will cause such data to be lost. If there is any data you wish to retain, then save the data to a commercially available memory card or external MIDI device. 3 4 Press the [ blinking. ]/[ ] buttons so that FACTORY RESET is Press the [ENTER] button. fig. 07. e 12 Getting Ready 5 Press the [ENTER] button. The confirmation message "Are You Sure?" appears in the display. fig. 08. e 6 Press the [ENTER] button to execute Factory Reset. The PLAY page returns to the display. * Pressing the [EXIT] cancels execution of Factory Reset. * If "Internal Write Protect= ON" message is displayed, press [DEC] to turn the setting OFF. After pressing [ENTER] to clear the message, press [ENTER] again to reset to the factory preset settings. For more information about the Internal Write Protect, please refer to Owner's Manual p. 122 13 Listening to the Demo Songs The XV-3080 features 8 internal demo songs. Now let's listen to the XV3080's awesome sounds and effects in Demo mode. fig. 09. e 1 Hold down the [EXIT] button and press the [ The DEMO PLAY page appears in the display. fig. 10. e ] button. All rights reserved. Unauthorized use of this material for purposes other than private, personal enjoyment is a violation of applicable laws. 2 Rotate the VALUE dial or press the [INC] / [DEC] buttons to select the song you want to hear. * Select "CHAIN PLAY" to hear all songs performed in order, starting with the first song. 3 4 Press [ENTER] to start demo song playback. Press [EXIT] to stop the Performance and return to the status in Step 2. Pressing the [EXIT] button again while the XV-3080 is in this status takes you out of the DEMO PLAY page. * No data for the music that is played will be output from MIDI OUT. 14 Playing Sounds The XV-3080 comes with a full palette of onboard sounds. The sounds that are used for ordinary play are called "Patches. " Let's first listen to some Patch sounds in Patch mode. Playing Patches (Phrase Preview Function) Even with no MIDI keyboard or sequencer connected, the XV-3080 allows you to check sounds using a number prepared phrases that are perfectly matched to highlight each type of Patch. fig. 11. e 1 Press the [PATCH] button, lighting the indicator. The PATCH PLAY page appears in the display. fig. 12. e Certain Patches may not be set with a suitable range. In such cases, press the [ ]/ 2 Press and hold down the [VOLUME] knob. The prepared phrase using the Patch is played while the knob is depressed. [ ] button to adjust the range to appropriate conditions (Octave Shift function: Owner's Manual, p. 20). You can select other Patches by rotating the VALUE dial or pressing the [INC] / [DEC] buttons. Let's select some other Patches and check out some of the sounds available. 15 Playing Sounds Selecting Patches The XV-3080 comes with a "Patch Finder" feature that allows you to quickly find any Patch. Selecting Categories (Patch Finder Function) fig. 13. e 1 2 Press the [PATCH] button, lighting the indicator. Press the [PATCH FINDER] button, lighting the indicator. On the display, the Patch's number is replaced by its category. fig. 14. e Category 3 4 5 Press the [ ]/[ ] button to select the desired category. For details on the categories you can select, refer to Owner's Manual p. 17. Turn the VALUE dial or press the [INC]/[DEC] button to select any Patch from the currently selected category. Press the [PATCH FINDER] button to turn off its indicator. 16 Playing Sounds * If you press the VALUE dial after Step 3, the CATEGORY SELECT page appears. fig. 13a. e You can change to another category on this page by holding down the [SHIFT] button and pressing [INC]/[DEC]. Turn the VALUE dial or press the [INC]/[DEC] button to select a category, and then press [ENTER] to confirm the selection. What is a Patch?With the XV-3080, the basic sound component used in a usual performance is referred to as a "Patch. " A single Patch can be created by combining up to four different tones. [. . . ] In this Performance, the note range settings for Part 2 and Part 3 are shown below. 27 Playing Sounds Part 2: C4­G9 Part 3: C -1­B3 Setting the Note Range of Each Part Now let's modify the settings so that Part 2 will sound in the C5­G9 range and Part 3 will sound in the C -1­B4 range. fig. 33. e 1 2 3 Make sure that Performance PR-B:29 Organ/Lead is selected. Press the [COMMON] function select button. Press [ fig. 34. e ]/[ ] to select the PART KEY RANG page. 4 5 Press the PART SELECT [2/10] button. Press the [ Upper. ]/[ ] button to move the cursor to Lower/ 28 Playing Sounds 6 Turn the VALUE dial to select the following values. Lower: C5 Upper: G9 7 8 Press the PART SELECT [3/11] button, set Lower to "C -1, " and set Upper to "B4" in the same way. Press the [EXIT] button to return to the PERFORM PLAY page. Play your MIDI keyboard and notice how the Parts' ranges have changed. 29 Playing Sounds Try Using an External MIDI Device to Switch Patches and Other Settings Using an External MIDI Device to Switch Patches and Rhythm Sets The XV-3080 can use received MIDI data to switch Patches (including the Patches in each part of a Performance) and Rhythm Sets. Here, after setting the send channel for the external MIDI device and the XV3080's receive channel (Patch/Rhy Rx Ch) to "1, " try sending a MIDI message from the external MIDI device to switch the XV-3080's Patch to PRA:002 Bright Piano. Executing Factory Reset sets the receive channel in Patch and Rhythm Set modes to "1. " 1 2 3 Use a MIDI cable to connect the MIDI OUT connector on the external MIDI device to the XV-3080's MIDI IN connector. Press the [PATCH] button, lighting the indicator. Set the channel used for transmission by the external MIDI device and the XV-3080's receive channel to the same channel (see p. 21). * Since the receive channel is always set to "1" when a Factory Reset is executed, it may not be necessary to set the receive channel. 4 Send a Bank Select MSB (Control Number 0) value of "87" to the XV-3080. * If you want to switch Rhythm Sets, send "86" as the value. 5 6 Next, send a Bank Select LSB (Control Number 32) value of "64. " When the XV-3080 receives a Program Change message without receiving any Bank Select as well, a Patch or Rhythm Set in the Preset, User, or other specified group is used. Send a Program Change with a value of "2. " The Patch name appearing in the page changes to PR-A:002 Bright Piano. fig. 39. e 30 Playing Sounds * Each Patch or Rhythm Set has a corresponding Bank Select number and Program number, as shown below. Patches Patch Group USER PR-A PR-B PR-C PR-D PR-E PR-F CD-A : CD-H XP-A : XP-F SR-JV80 Series SR-JV80-01 SR-JV80-01 SR-JV80-02 SR-JV80-02 : SR-JV80-65 SR-JV80-65 Patch number 001­128 001­128 001­128 001­128 001­128 001­128 001­128 001­128 : 001­128 *1 : *1 Patch number 001­128 129­256 001­128 129­256 : 001­128 129­256 Bank Select number MSB LSB 87 00 87 64 87 65 87 66 87 67 87 68 87 69 87 32 : : 87 39 *1 *1 : : *1 *1 Bank Select number MSB LSB 89 00 89 01 89 02 89 03 : : 91 00 91 01 Program number 001­128 001­128 001­128 001­128 001­128 001­128 001­128 001­128 : 001­128 *1 : *1 MIDI data can also be used to switch among Patch, Rhythm Set, Performance, and GM modes (Owner's Manual; p. [. . . ]