Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... DON'T FORGET : ALWAYS READ THE USER GUIDE BEFORE BUYING !!!
If this document matches the user guide, instructions manual or user manual, feature sets, schematics you are looking for, download it now. Lastmanuals provides you a fast and easy access to the user manual ROLLS MX34B. We hope that this ROLLS MX34B user guide will be useful to you.
Lastmanuals help download the user guide ROLLS MX34B.
Detailed instructions for use are in the User's Guide.
[. . . ] Two 9 volt alkaline batteries ensure adequate signal strength as well as phantom power for your favorite condenser microphone. Please review this manual carefully as it contains important information regarding the proper use of this product.
SPECIFICATIONS Input Impedance: mic aux Output Impedance: THD + Noise: S/N Ratio: Frequency Response: Max Output Level: Max Input Level: Max Gain: Batteries: Current Draw: Phantom Power: Input Connectors: DC Power Jack: Output connectors: 600 Ohms or greater XLR 47K stereo 3. 5mm 50 Ohms . 02% 110 dB 20 Hz - 30 kHz (+0 / -1 dB) + 14 dB +20 dB +70 dB 2 X 9V Alkaline 30 mA +18 VDC 2 Female XLR, 1/8" (3. 5mm) (5. 5 X 2. 1 mm tip negative) 3. 5mm stereo main out 3. 5mm Headphone 6. 3"w x 3. 7"d x 1. 4" h 1 lbs.
INSPECTION
1. Unpack and Inspect the MX34b package Your MX34b was carefully packed at the factory in a protective carton. [. . . ] OUTPUT: 1/8" (3. 5mm) jack containing the Headphone Output signal. REAR PANEL
INPUTS: 1 - 2: XLR balanced inputs for connection to any standard dynamic or condenser microphone. The input circuitry has a very wide input range and can accomodate almost any (mic to line) level signal. AUX IN: Tip-Ring-Sleeve stereo 1/8" (3. 5mm) jack for connecting to another line-level stereo signal source. STEREO OUT: Tip-Ring-Sleeve stereo 1/8" (3. 5mm) jack for connection to a camera or other stereo input (Line-level only). 12 VDC jack: For connection to the Rolls PS27 12VDC power supply. POWER: Button applies power to the MX34b. BATTERY INSTALLATION: To replace the 9 V alkaline batteries, first carefully press in and up on the door to release the battery compartment. It then slides out and you can replace the battery. Remember to replace both batteries at the same time. PHANTOM POWER: The Phantom Power jumpers are set to the off position from the factory. To engage the phantom power, first make sure the MX34b is powered off, use a pair of needle-nose pliers or tweezers and carefully pull out the jumper corresponding to the channel you wish to power. Replace the jumper - connecting the two pins labeled on. 5
2
CONNECTION Connect microphones to the MX34b via balanced XLR cables. [. . . ] Adjust the Headphone Level control for a comfortable listening volume. For best results, we recommend recording a couple of test runs to ensure you have proper levels set.
HEADSET MIC 1/8"
b
When the signal becomes weak and distorted, and the pwr LED dims, the batteries will need replacing. See page 2; Battery Installation for details.
Connect STEREO headphones or earphones to the 1/8" (3. 5mm) HEADPHONE OUTPUT located on the MX34b front panel.
NOTE: ON CONNECTING A WIRELESS MIC TO THE AUX INPUT
DO NOT CONNECT A MONO PLUG TO SLEEVE MONO PLUG THE AUX IN OR STEREO OUTPUT. [. . . ]
DISCLAIMER TO DOWNLOAD THE USER GUIDE ROLLS MX34B
Lastmanuals offers a socially driven service of sharing, storing and searching manuals related to use of hardware and software : user guide, owner's manual, quick start guide, technical datasheets... In any way can't Lastmanuals be held responsible if the document you are looking for is not available, incomplete, in a different language than yours, or if the model or language do not match the description. Lastmanuals, for instance, does not offer a translation service.
Click on "Download the user manual" at the end of this Contract if you accept its terms, the downloading of the manual ROLLS MX34B will begin.
