User manual ROLLS RP262

[. . . ] In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. [. . . ] Please read the following manual carefully to ensure proper operation, and enjoy your new RP262. Unpack and inspect the RP262 box and package. If obvious physical damage is noticed, contact the carrier immediately to make a damage claim. We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Please complete the Warranty Registration Card and return it to the factory. NRTL /C R LEFT LEFT LEFT LEFT INSERT INSERT INSERT INSERT RIGHT RIGHT RIGHT RIGHT LINE LINE LINE LINE MIXER AUX 1 AUX 2 RIGHT OUT RET. LEFT AUX 1 OUT +60 TRIM +10 MIC 11/12 +60 TRIM +10 MIC 9/10 +60 TRIM +10 MIC 7/8 +60 TRIM +10 MIC 5/6 MIC 4 +60 TRIM +10 MIC 3 +60 TRIM +10 MIC 2 +60 TRIM +10 MIC 1 +60 TRIM +10 MODEL RP262 MADE IN U. S. A. SERIAL NUMBER 262- LEFT RIGHT 120 VAC 50/60 Hz 15 VA RISQUE DE CHOC - NE PAS ENLEVER WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. RIGHT OUTPUT LEFT OUTPUT RIGHT LEFT OUTPUT OUTPUT OUTPUT INPUT RIGHT INPUT LEFT INPUT RIGHT INPUT LEFT INPUT SUB OUTPUT 4A 120V - 2A 230 V OUTPUT 2 OUTPUT 1 SERIAL NUMBER OUTPUT 1 MADE IN U. S. A. BRIDGE NORMAL SPECIFICATIONS Frequency Response: Input Impedance: THD + Noise: Noise Floor: Subwoofer Slope: Max. Subwoofer Gain: Indicators: C O R P O R A T IO N POWER AMPLIFIER MAINS POWER WARNING For continued prootection against risk of fire, replace only with same type and rating of fuse. + CAUTION + OUTPUT 2 CHANNEL 2 INPUT CHANNEL 1 INPUT TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE LID. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL WARNING: To reduce the risk of electric shock or fire do not expose this device to rain or moisture. RISQUE DE CHOC - NE PAS ENLEVER SERIAL NUMBER 120 VAC 50/60 Hz 15 VA MODEL RA235 235- OUTPUTS CHANNEL ONE INPUTS CHANNEL ONE MADE IN U. S. A. SUB-WOOFER AMPLIFIER WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC - NE PAS ENLEVER Input/Output jacks (2 ea. ) Dimensions: Weight: Power: 20Hz to 40kHz 10K balanced 10K unbalanced <0. 07% typical -78 dB -18 dB/Octave +20 dB Power LED Active LED 2: 5-segment LED level meters Sub Clip LED XLR balanced 1/4" unbalanced RCA unbalanced 1. 75" x 6" x 19" (89mm x 162mm x 482mm) 6 lbs. (2. 72 Kg) 120VAC (230VAC) 15VA FRONT PANEL DESCRIPTION SUB FREQU E N C Y: Sets the highest frequency allow ed out of the Sub W o fe or Outputs. This frequency is adjustable between 35Hz and 200Hz. SUB LEVEL: Adjusts the output level of the Sub W o fer Outputs. The leve i o ls adjustable between -infinity (off) and a gain of +20 dB. SUB CLIP LED: When lit, this LED indicates the signal level is 3 dB below clipping and there may be distortion in the Sub W o fe c r u t o r i c i s. ACTIVE SWITCH: Engages and disengages the RP262 process. When out, the efe t i bypassed. fc s B OTTOM: Controls the low frequency cut/boost (flat or no cut/boost is at about 11 O'clock. There is a 0 to 1/2 turn spectrum spread from mid-range to bass with ) this control as well as amplitude control. DEFINITION: Controls the amount of sonic clarity and sound spread. S t i g i o etn t n 0 is flat response and minimal spread, on 10 is maximum spread and definition. [. . . ] ult RIGHT/LEFT XLR OUTPUTS: Balanced outputs for connection to a pow e r a p i i r. mlfe RIGHT/LEFT 1/4" OUTPUTS: Unbalanced outputs. LEFT/RIGHT 1/4" INPUTS: Unbalanced inputs for connection (normally) to the ls d a t evice in the signal chain before the pow e a p i i r. [. . . ]