User manual ROLLS RP562

[. . . ] A sonic exciter restores clarity and presence to the processed signal by correcting phase changes and harmonic structure differences. In other words, it puts the components of the sound back where they belong. RIGHT RIGHT RIGHT RIGHT LINE LINE LINE LINE MIXER AUX 1 AUX 2 RIGHT OUT RET. LEFT AUX 1 OUT +60 TRIM +10 MIC 11/12 +60 TRIM +10 MIC 9/10 +60 TRIM +10 MIC 7/8 +60 TRIM +10 MIC 5/6 MIC 4 +60 TRIM +10 MIC 3 +60 TRIM +10 MIC 2 +60 TRIM +10 MIC 1 +60 TRIM +10 MODEL RP562 MADE IN U. S. A. RP562 RIGHT OUTPUT LEFT OUTPUT SERIAL NUMBER 562- 120 VAC 50/60 Hz 15 VA WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. RIGHT LEFT OUTPUT OUTPUT RISQUE DE CHOC - NE PAS ENLEVER RIGHT INPUT LEFT INPUT RIGHT INPUT LEFT INPUT SUB OUTPUT 4A 120V - 2A 230 V OUTPUT 2 OUTPUT 1 SERIAL NUMBER OUTPUT 1 MADE IN U. S. A. BRIDGE NORMAL CORPORATION POWER AMPLIFIER MAINS POWER + CAUTION + OUTPUT 2 CHANNEL 2 INPUT CHANNEL 1 INPUT TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE LID. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL Using a vacuum tube circuit in this configuration not only restores the clarity lost in previous processes, it adds warmth and a slightly compressed attribute to the program material. [. . . ] We suggest saving the shipping carton and packing materials for safely transporting the unit in the future. Please complete the Warranty Registration Card and return it to the factory. WARNING For continued prootection against risk of fire, replace only with same type and rating of fuse. WARNING: To reduce the risk of electric shock or fire do not expose this device to rain or moisture. RISQUE DE CHOC - NE PAS ENLEVER SERIAL NUMBER 120 VAC 50/60 Hz 15 VA MODEL RA235 235- OUTPUTS CHANNEL ONE INPUTS CHANNEL ONE MADE IN U. S. A. SUB-WOOFER AMPLIFIER WARNING: DO NOT EXPOSE THIS EQUIPMENT TO RAIN OR MOISTURE. TO REDUCE THE RISK OF ELECTRIC SHOCK DO NOT NOT REMOVE BACK. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL RISQUE DE CHOC - NE PAS ENLEVER 4 1 FRONT PANEL DESCRIPTION SUB FREQUENCY: Sets the highest frequency allowed out of the Sub Woofer Outputs. This frequency is adjustable between 35Hz and 200 Hz. SUB LEVEL: Adjusts the output level of the Sub Woofer Outputs. The level is adjustable between - infinity (off) and a gain of + 20 dB. SUB CLIP LED: When lit, this LED indicates the signal level is 3 dB below clipping and there may be distortion in the Sub Woofer circuits. ACTIVE SWITCH: Engages and disengages the RP562 process. BOTTOM: Controls the low frequency cut/boost (flat or no cut/boost is at about 11 o'clock). There is a 0 to 1/2 turn spectrum spread from midrange to bass with this control as well as amplitude control. DEFINITION: Controls the amount of sonic clarity and sound spread. Setting it on 0 is flat response and minimal spread, on 10 is maximum spread and definition. This is also a good setting for constant dispersion horns. LEFT/RIGHT LEVEL LEDS: Indicates the output level of each channel. PWR LED: Indicates that the RP562 is connected to an AC outlet, and the power is turned on. POWER SWITCH: Controls the primary power to the RP562. SUB FREQUENCY 100 ACTIVE OPERATION STEREO CONNECTION The diagram shown below is a stereo connection for your RP562. We recommend you put the RP562 last in the signal chain. [. . . ] Products returned to us or to an authorized Service Center must be accompanied by a copy of the purchase receipt. In the absence of such purchase receipt, the warranty period shall be one (1) year from the date of manufacture. This warranty shall be invalid if the product is damaged as a result of defacement, misuse, abuse, neglect, accident, destruction or alteration of the serial number, improper electrical voltages or currents, repair, alteration or maintenance by any person or party other than our own service facility or an authorized Service Center, or any use violative of instructions furnished by us. This one-year warranty is in lieu of all expressed warranties, obligations or liabilities. [. . . ]