User manual ROSE DISPLAYS ANOGOTCHA STAND

[. . . ] AnoGotcha Stand TM Parts Read this instruction sheet carefully before assembly. Separate all parts and check quantities. Make sure all parts are accounted for before discarding any packaging materials. [. . . ] Part #02INSAnoGotchaStand 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 3 · Slide one T-Gotcha holder into each AnoGotcha shell. · Attach one shaped end cap onto each end of both AnoGotcha shells. assembly continued Insert T-Gotcha holders into AnoGotcha shells. shaped end cap AnoGotcha shell T-Gotcha Slide T-Gotcha holder into each AnoGotcha shell as shown. Attach one shaped end cap onto each end of AnoGotcha holders, as shown. You should have two AnoGotcha holders with one shaped end cap on each end. Step 4 Attach top AnoGotcha holder onto vertical poles. · Slide one threaded rod with ball knob (created in step 1) through top hole in one vertical pole (created in step 2). · Slide threaded rod completely through top channel of one AnoGotcha holder (created in step 3) and through top hole of second vertical pole. · Screw second ball knob onto other end of threaded rod. Tighten securely. ball knobs top AnoGotcha holder 9" round base Slide threaded rod through the top hole of one vertical pole and then through top channel of one AnoGotcha holder. Slide threaded rod through top hole in second vertical pole. Screw ball knob tightly onto threaded rod. vertical pole Your stand should now look like this. AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSAnoGotchaStand 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com AnoGotchaTM Stand Step 5 · Choose the height slot that matches the length of your graphic. · Slide one threaded rod with ball knob (created in step 1) through appropriate hole in one vertical pole (created in step 2) and through bottom channel of one AnoGotcha holder (created in step 3). · Slide threaded rod through corresponding slot of second vertical pole. Note: Make sure the hinge on the bottom T-Gotcha faces up and in the same direction as the hinge on the T-Gotcha at the top of the stand. · Loosely screw second ball knob onto end of threaded rod. Note: Ball knob must be kept loose until graphic is inserted. 28" 28" assembl y continued Attach bottom AnoGotcha holder to vertical poles. 48" 60" Bottom AnoGotcha must be attached at slot that matches the length of your graphic. T-Gotcha hinge must face up and in the same direction as T-Gotcha on the top. 48" 60" Slide threaded rod through height slot that matches the length of your graphic and through bottom channel of remaining AnoGotcha holder. AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. [. . . ] Turn ball knob in your right hand away from you. If you have any questions about your AnoGotcha Stand assembly, please call Rose Displays at 1-800-631-9707 and we will assist you. AnoGotcha is a registered trademark of Rose Displays, Ltd. Neither the manufacturer nor any sales agent may be held liable for injury, loss or damage resulting from the use of these products. Part #02INSAnoGotchaStand Your completed AnoGotcha Stand should look similar to this. 35 Congress Street, Salem, MA 01970 Tel# 1- 800 631-9707 Fax# 1-800-560-2890 e-mail:signware@rosedisplays. com [. . . ]