User manual ROSEN DA-7169 REV B

[. . . ] power off the unit and consult your dealer immediately. Do not open the unit; there are no serviceable parts inside. · If the unit shows signs of overheating or malfunction, To avoid damaging the LCD panel: · Do not drop the LCD display panel or subject it to direct impact. · If the LCD panel breaks, avoid contact with any broken glass or leaking fluids. If you come into contact with these materials, flush and clean the affected areas with water. Seek medical attention immediately. This unit uses high-quality electronic components and is manufactured under a stringent quality-control system. [. . . ] Failure to connect the red and yellow wires properly may drain the vehicles battery. 7 To avoid damaging the unit, use only the accessories supplied with the unit. 8 Do not install this product at an angle exceeding ±30°. 9 Do not install this product in a position that may cause injury to passenger(s) during an accident. Page 4 2 Installing the DA-7169 Monitor Electrical Connections Color Code Black Red Yellow Blue Function Ground ACC +12 V +12 V Out (Max 1 Amp) Page 5 2 Installing the DA-7169 Monitor Signal Connections Color Code Grey /Yellow Black /Yellow Black/Black Orange/Brown Function Video 1 In Video 2 In Video Out Rear View Camera/Night Switch Signal Signal & Control Signal & Control Page 6 2 Installing the DA-7169 Monitor Typical Wiring Diagram The following is a typical wiring diagram for an In-Dash DA7169 connected to model DVA-310x and a radio receiver with a 40-Watt, 4-channel power amplifier. Page 7 3 Parts Overview Front Panel 1 2 3 4 5 6 7 8 9 7/8/9 10 11 12 13 14 15 16 Mute (MUTE) Remote sensor Signal Source select (SRCE and CH / AV1 / AV2) Player select and Play/Pause (DISC & PLAY / PAUSE) AM/FM Radio select (BAND & AM/FM; when interfaced with DA-2301) OPEN / CLOSE Disc select +/- (DISC) Audio select (AUDIO) Repeat function (REP) Memory location (1 / 2 / 3 / 4 / 5 / 6) Forward (>) Up volume control Backward (<) Function mode (SEL) Down volume control Degree of tilt (ANGLE) Display mode (WIDE) Page 8 3 Parts Overview Remote Control Unit Frequently Used Buttons CHANNEL SELECT: Selects TV channels, disc title, or desired settings on the MENU screen. MENU: Displays menu screen of functions available. POWER: Open (ON) or close (OFF) the monitor enclosure. VIEWING ANGLE & DISPLAY MODE: Press once to activate angle adjustment function. While in this mode, press por q to set the tilt angle of the screen. Press and hold to activate display mode functions: ZOOM / CINEMA / NORMAL / FULL. Page 9 3 Parts Overview Replacing the Battery 1 Use a small coin to remove battery container from the unit. 2 Remove old battery and insert new one. The positive sign (+) should face upward. 3 Insert battery container into unit until it is securely in place. Precautions 1 Properly dispose of used battery. 2 Overheating the battery may cause an explosion or create a fire hazard. 3 Remove used batteries from the battery container to prevent leakage. 4 Prevent children from playing with the battery. Page 10 4 Operating the DA-7169 Monitor Operating the In-Dash DA-7169 Color Display Monitor To take full advantage of the In-Dash DA-7169s features, read these operating instructions before using the monitor. Note: The color and brightness of the LCD display screen is factory preset. To adjust picture quality, follow the instructions in this guide. Ejecting and Opening the Display Monitor · To eject/open the display monitor, press the OPEN / CLOSE button (#6 on the Front Panel Overview on page 7) once. The display monitor will automatically eject from its DIN enclosure. Caution: To prevent damage to the driver motor and gear train, do not obstruct the movement of the monitor tray. · If the ejection of the display monitor is stopped halfway, press the OPEN / CLOSE button once to return the monitor to the closed position. Press OPEN / CLOSE to activate the ejection process again until the monitor is fully extended. the ignition is turned OFF or when pressing the OPEN / CLOSE button when the monitor is in the open position. · The display monitor returns to the closed position when Adjusting the Position of the Monitor · Press the ANGLE + / - button (#15) to adjust the viewing angle of the monitor. Page 11 4 Operating the DA-7169 Monitor Note: To prevent damage to the gear train, do not use force to adjust the display screen. · The display monitor returns to the preset position whenever the system is turned ON. [. . . ] Note: Refer to Choosing NTSC or PAL Display System on previous page. Note: The SRCE button activates TV (CH) mode when the monitor is connected to model DA-2301. Selecting the Audio Channel · Use the AUDIO button (#8) to select the desired channel when the monitor is connected to a DVD player or VCD/ CD changer (model DA-2301). guage as recorded in the DVD. · The AUDIO button is also used to select the audio lan· When playing back VCD, use the AUDIO button to toggle between AUDIO LL, AUDIO RR, or AUDIO STEREO. [. . . ]