User manual ROSIERES VE 60

[. . . ] Then fit the upper bracket complete with baffle to the ceiling using the screws provided (Fig. Fix the telescopic flue by means of the supplied side fixing screws (Fig. Also remember that charcoal filters must be used in the case of the filtering version; check to see whether such filters are already fitted; if necessary, proceed to fit as follows, depending on the model type purchased: - if the hood features round charcoal filters (Fig. 14), fit the charcoal filter by turning anti-clockwise. [. . . ] Button D: drives the motor in third speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on), the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). Button E: drives the motor in fourth speed (the corresponding pilot lamp comes on); when pressing the button a second time (while the pilot lamp is on), the TIMER is activated and thus the motor stops after 5' (the pilot lamp flashes). 10: P1 Switches LIGHTS on and off P2 min and MAX LIGHT intensity P3 Nothing happens when pressed with motor OFF. When pressed with motor ON decreases speed until switchoff. Kept pressed for 2" with motor OPERATING, switches off motor and stores the speed. P4 When pressed with motor OFF, switches on the motor at stored speed in switch-off or first speed phase When pressed with motor ON, increases speed. L1 and shows current speed (GREEN) P5 Resets filter reset count with motor OFF. NOTE The filter timer is maintained even in the absence of power With motor ON, trigger TIMER 5' L2 Shows: 1) with motor off, the FILTER RESET IN RED, (30hours Steady LED, 120hours flashing LED) 2) In FLASHING GREEN the TIMER 5' CONTROLS shown in Fig. 11: Key A = switches off lights; if the key is pressed while the lights are on, light intensity drops as far as zero; if the key is kept pressed for a few seconds, the lights go out. The lights come on according to the last level of intensity set. By pressing the key while the lights are on, light intensity increases; by keeping the key pressed for a few seconds, light intensity goes directly to maximum level. If the instructions for installation for the hob specify a greater distance, this has to be taken into account. The air collected must not be conveyed into a duct used to blow off smokes from appliances fed with an energy other than electricity (central heating systems, thermosiphons, water-heaters, etc. Comply with the official instructions provided by the competent authorities in merit when installing the disposal duct. In addition, exhaust air should not be discharged into a wall cavity, unless the cavity is designed for that purpose. The room must be well aerated in case a hood and some other heat equipment fed with an energy other than electricity (gas, oil, coal heaters, etc) operate at the same time. In fact the intake hood, disposing of air, could create a vacuum in the room. the vacuum should not exceed 0 , 04mbar. This prevents the gas exhausted by the heat source from being intaken again. It is therefore advisable to ensure the room contains air taps able to ensure a steady flow of fresh air. Check the data label inside the appliance; if the symbol ( ) is printed, read the following: this appliance has such technical particulars that it belongs to class II insulation, therefore it must not be earthed. The following warning is valid in the United Kingdom only: in case your cable is not furnished with a plug, read the following instructions; as the colours of the wires in the mains lead of this appliance may not correspond with the coloured markings identifying the terminals in your plug, proceed as follows: ­ the wire which is coloured blue must be connected to the terminal which is marked with the letter N or coloured black; ­ the wire which is coloured brown must be connected to the terminal which is marked with the letter L or coloured red. [. . . ] In case your appliance is not furnished with a non separating flexible cable and has no plug, or has not got any other device ensuring omnipolar disconnection from the electricity main, with a contact opening distance of at least 3 mm, such separating device ensuring disconnection from the main must be included in the fixed installation. If your unit features a power lead and plug, position this so the plug is accessible. Always switch off the electricity supply before carrying out any cleaning or servicing operations on the appliance. Avoid using materials which could cause spurts of flame (flambées) near the appliance. [. . . ]