User manual ROTEL RHB-200

[. . . ] CD AV TUN MP3 OFF MUTE V V RKP-200 Learning Keypad Keypad Connecting Hub RHB-200 2 RKP-200/RHB-200 1. RKP-200 Keypad CD AV TUN MP3 ZONE IN OFF MUTE V V ZONE OUT 2. RHB-200 Connecting Hub ZONE1 IN DC 12V ZONE2 IN CLONE IN IR OUT ZONE1 ZONE2 ZONE3 ZONE4 COMMON IR OUT ZONE3 IN ZONE4 IN 3 3. Connecting Keypads ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN ZONE OUT OFF MUTE V V OFF MUTE V V ZONE OUT ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN LIGHT ZONE OUT LIGHT ZONE OUT OFF MUTE V V OFF MUTE V V ZONE1 IN DC 12V ZONE2 IN CLONE IN IR OUT ZONE1 ZONE2 ZONE3 ZONE4 COMMON IR OUT ZONE3 IN ZONE4 IN ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN ZONE OUT OFF MUTE V V OFF MUTE V V ZONE OUT 4 RKP-200/RHB-200 4. Connecting RHB-200 ZONE1 IN DC 12V ZONE2 IN CLONE IN IR OUT ZONE1 ZONE2 ZONE3 ZONE4 COMMON IR OUT ZONE3 IN ZONE4 IN POWER 1 4 7 +10 TUNE 2 5 8 0 3 6 ON OFF CH VOL 9 MEM SMART X GUIDE C CTR SMT MUTE MENU FRQ DIRECT M OSD PRESET ENT FM MONO BAND SEARCHSEARCH+ S SUB R SUR AUD CD TUN TAPE EXT DEVICE / INPUT V1 V2 V3 V4 V5 RR-1060 5 5. Clone setup ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN ZONE OUT OFF MUTE V V OFF MUTE V V ZONE OUT ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN ZONE OUT OFF MUTE V V OFF MUTE V V ZONE OUT CD AV TUN MP3 ZONE IN ZONE1 IN DC 12V ZONE2 IN CLONE IN IR OUT ZONE1 ZONE2 ZONE3 ZONE4 COMMON IR OUT OFF MUTE V V ZONE OUT ZONE3 IN ZONE4 IN ZONE IN CD AV TUN MP3 CD AV TUN MP3 ZONE IN ZONE OUT OFF MUTE V V OFF MUTE V V ZONE OUT 6 RKP-200/RHB-200 Contents 1. Clone setup 2 2 3 4 5 Connecting the system . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 8 Cable selection 8 Connecting Master Keypads 8 Connecting a Second Keypad 8 Mounting the Keypads Connecting the RHB-200 to a Rotel Receiver Connecting the RHB-200 to Source Components AC Power connection 9 9 9 9 Introduction . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 7 Key Features 7 RKP-200 Overview . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] Therefore, customizing should be completed before mounting the keypads. The location of the DIP switches can be seen in Figure 1 at the front of this manual. Here are the default settings for all ten switches: 12 RKP-200/RHB-200 NOTE: Details of the switch settings are provided with the instructions for each configuration option, but here is a summary: SW1: SW2: SW3: SW4: SW5: SW6: SW7: SW8: SW9: SW10: Used for invisible layer command programming for the CD device. Used for invisible layer command programming for the TUN device. Used for invisible layer command programming for the AV device. Used for invisible layer command programming for the MP3 device. In the ON position, enables the ton as an additional device key. but Flashing button illumination provides confirmation and error indications during the Learning and SMART sequence programming. The backlighting should be enabled during configuration. Disabling IR Sensor An IR sensor on the front of the keypad allows operation of the system from a handheld remote control aimed at the keypad. Generally, the sensor only needs to be disabled when two keypads are installed in the same room. In this case, disable the sensor on the second keypad to prevent sending IR commands to both keypads. For the same reason, you might disable the sensor of a keypad installed near the components being controlled. SW9 configures the sensor mode: To enable the IR sensor, put SW9 in the ON position. In the ON position, enables the button as an additional device key. Enables the learning mode in the ON position. Enables the SMART programming mode in the ON position. Enables (ON) or disables (OFF) the IR sensor on the front of the keypad. Enables (ON) or disables (OFF) the backlighting feature. To disable the IR sensor, put SW9 in the OFF position. Disabling Backlighting The RKP-200 backlighting feature illuminates a device button as a reminder of the selected device as well as the button when the sound is muted. SW10 configures the backlighting mode: To enable the backlighting, put SW10 in the ON position. NOTE: Learning commands is done by aiming a handheld remote at the keypad sensor. The sensor must be enabled during Learning configuration. Optional Device Buttons The keypad has four permanent device buttons: , , , . These device buttons select a source component for listening and operation. Pressing a device button makes the normal commands on the other ten buttons available. Device buttons cannot store normal learned commands; however, they can store a SMART sequence of normal commands that is sent when the device button is pressed. [. . . ] While this keypad is receiving cloned data, the ZONE 1 LED on the front of the RHB-200 flashes red. When the cloning of the first keypad is complete, the LED glows solid red. The cloning process then continues to the second keypad in ZONE 1 (if it exists). The LED flashes green during the cloning and glows solid green when the cloning is complete. [. . . ]