User manual ROTEL RSP-966

[. . . ] RSP-966 SURROUND SOUND PROCESSOR SURROUND SOUND PROCESSOR RSP-966 MASTER VOLUME POWER REMOTE SENSOR VIDEO1REC VIDEO2 VIDEO 3 VID4AUX TAPE2M MEMORY OSD OPTICAL COAXIAL 1 MPEG dts Digital Pro Logic 3 Stereo DSP MODE 5. 1 CH D. RANGE SLEEP 3 2 4 STANDBY STANDBY SOURCE PHONO TUNER CD TAPE 1 TAPE 2 MONITOR VIDEO 1 VIDEO 2 VIDEO 3 VIDEO 4 AUX/ VIDEO 5 PRO-LOGIC 3 STEREO DSP STEREO DYNAMIC RANGE 5. 1 CH INPUT SPEAKER MODE ENTER VIDEO LABELS VIDEO 1 REC BASS TREBLE BALANCE ­ SUBWOOFER + ­ REAR + ­ CENTER + Owner's Manual D SURROUND SOUND PROCESSOR RSP-966 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. WARNING: There are no user serviceable parts inside. Refer all servicing to qualified service personnel. [. . . ] Use the SMALL position if your center channel speaker has more limited low frequency capability, or if you prefer that the bass be sent to the subwoofer. Select the NONE setting if your system does not have a center channel speaker. REAR SPEAKERS (small/large/none): If your rear surround speakers are capable of sustained low frequency output, select the LARGE setting (not available with SMALL front speakers). If your rear speakers have limited bass capability or if you would prefer that the bass go to a subwoofer, use the SMALL setting. If your system has no rear surround speakers, select the NONE setting (surround information will be added to the front speakers). SUBWOOFER (yes/no): Use the YES setting if your system has a subwoofer. If your system does not have a subwoofer, select NO. Note 1: Speaker configuration need only be done one time. The configuration will apply to all surround modes. Note 2: The available options during the configuration procedure may vary depending on the current surround mode setting. For this reason, select one of the surround modes, either Dolby Pro Logic or Dolby Digital, before setting the speaker configuration. Note 3: Dolby Digital and DTS modes are automatically activated based on software codes; there is no manual mode setting. Therefore, to use one of these modes for configuring the speaker settings, play a Dolby Digital or DTS digital recording to activate these modes and then press the SPEAKER MODE button to configure the speakers. There are two ways to configure your speaker system. One is the ON-SCREEN MENU system (described later in this manual). The other method uses the front panel SPEAKER MODE button: 1. Select the Dolby Pro Logic surround mode with the front panel buttons or by playing a Dolby Digital or DTS digital source. Press and hold the SPEAKER MODE button for at least 2 seconds to activate the FRONT speaker configuration. An indicator will appear in the front panel display. Quickly press the SPEAKER MODE button in succession to toggle through the available options for the FRONT speakers (large/small). The selection will appear on front panel display. When the correct size configuration for your FRONT speakers appears, press the ENTER button to store the setting. This will automatically take you to the configuration options for the next type of speaker, for example, the CENTER speaker. Repeat steps 3 and 4, pressing the SPEAKER MODE button quickly in succession until you reach the desired setting and then confirm the selection by pressing the ENTER button. [. . . ] SPL meters are available from electronics stores, or your authorized Rotel dealer may loan you one. Set the meter to its SLOW response time with C-weighting and be sure to hold it away from your body. The goal is to adjust each speaker so that the meter provides the same reading for each of the speakers in your system. 20 RSP-966 TONE/BALANCE Menu TONE / BALANCE SETUP Menu SETUP MENU Front: Rear: Center: Subwoofer: Dynamic Range: Menu Display: LARGE SMALL LARGE YES OFF SCREEN Bass : +10dB Treble : +10dB Balance : L 10 DOWN­selection VOLUME­change BACK-return MENU-screen off DOWN­selection ENTER­change BACK-return MENU-screen off This menu duplicates the functions of the front panel TREBLE, BASS, and BALANCE controls and provides a method of changing them with the remote control. Select a line in the menu using the UP/DOWN buttons on the remote, then adjust the setting using the VOL UP/DOWN remote buttons. [. . . ]