User manual ROTEL RT-560

[. . . ] Do not allow foreign objects to get into the enclosure. If the unit is exposed to moisture, or a foreign object gets into the enclosure, immediately disconnect the power cord from the wall. Take the unit to a qualified service person for inspection and necessary repairs. Read all the instructions before connecting or operating the component. [. . . ] To reduce the input level of an analog input: 1. Press and hold the AG/DG button (front panel only), to toggle between no attenuation (ATT NORMAL appears in the display) and attenuation on (ATT ON appears in the display). NOTE: This setting must be made individually for each analog input and is memorized as a permanent setting. Dolby Surround Dolby Pro Logic II The most widely available surround sound format for consumer audio/video is Dolby Surround®, available on nearly all commercial VHS tapes, many television broadcasts, and most DVDs. It is a matrix-encoding system that records front left, front center, front right, and a mono surround channel into a 2channel stereo recording. During playback, a Dolby Pro Logic® or Pro Logic II decoder extracts each channel and distributes it to the appropriate speakers. Dolby Pro Logic II decoding should be used for any analog recording labeled "Dolby Surround" or any Dolby Digital 2. 0 soundtrack. A "music mode" makes Pro Logic II an excellent choice for audio CDs. Dolby Pro Logic Cinema or Music modes can be selected for ANY 2-channel recording, analog or digital. The built-in DVD input always uses digital signals and cannot be changed. This setting is memorized independently for all other digital inputs. NOTE: Selecting the Digital Signal P6-D When the DIGITAL AUTO mode is selected and a digital signal is detected, one of four indicators appears in the display, depending on the type of digital signal being received: DOLBY DIGITAL: Dolby Digital signal is being received. LPCM: Linear PCM signal (such as a CD) is being received. PPCM: DVD AUDIO Packed PCM digital signal is being received. In almost all cases, the correct type of digital signal is detected and decoded automatically in DIGITAL AUTO mode. An indicator in the frontpanel display confirms your choice and the currently tuned station frequency is shown. DVDs with a DTS soundtrack almost always have it configured as an option to the standard matrix Dolby Surround format. To use DTS, you may have to go to the setup menus at the beginning of the DVD and select "DTS 5. 1" instead of "Dolby Surround" or "Dolby Digital 5. 1". NOTE: These settings are memorized independently for each source input and will be used as a default setting each time that source is used. NOTE: Tuning from the Front Panel 1. Repeatedly press the CONTROL buttons until the word TUNING appears in the front panel. Repeatedly press one of the CONTROL buttons until the desired frequency appears in the display. For seek tuning, press and hold one of the CONTROL buttons. When you release the button, the tuner will continue increasing or decreasing the frequency until the next available station is found. Surround Sound On/Off P2-G Press the SURROUND ON/OFF button on the front panel or the S-ON/OFF button on Page 2 of the remote to switch between Surround Sound On mode and Surround Sound Off (2ch stereo) mode. 23 English Tuning from the Remote P4-E 1. Repeatedly press the CH +/­ hard buttons or the TUNING commands on Page 4 of the remote until the desired frequency appears in the display. For seek tuning, press and hold one of the CH +/­ or TUNING buttons. When you release the button, the tuner will continue increasing or decreasing the frequency until the next available station is found. PRESET 5: PRESET 15: PRESET 25 Press: 5 Press: +0 > 5 Press: +0 > +0 > 5 DVD PLAYER 4. Press the MEMORY button again to store the preset. To memorize another station, press the TUNING buttons to tune to the desired station and repeat steps 2 through 4. NOTE: There is a time limit for these steps. [. . . ] · ON: Select to enable the Guide feature. · OFF: Select to disable the Guide feature. 3. Press the CURSOR buttons to scroll though the list of country codes and highlight a selection. The highlight cursor moves to the SET LEVEL field. 5. [. . . ]