User manual ROWENTA SO9020

[. . . ] This documentation is therefore supplied under exclusion of any liability or warranty of suitability for specific purposes. innovaphone reserves the right to improve or modify this documentation without prior notice. Copyright 2009 innovaphoneP AG Bblinger Str. 76, 71065 Sindelfingen Tel: +49 7031 73009 0 Fax: +49 7031 73009 99 http://www. innovaphone. com P Table of contents About this manual . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . [. . . ] When you have ended the active call in this mode, the first call waiting in the wait list will call you. If you do not want to pick up the call, then press the clear key to reject it. in mode 2 Mode 2 Operating Manual IP Telephone SO9020 - 16 -- 16 - Key 0 Effect Press these keys in sequence to delete the waiting call displayed from the wait list. However, this is only possible if the call to be deleted in the wait list has not already been picked up. Thus it must be a call waiting ( ) and not a call-on-hold in the wait list( ) In order to terminate a call-on-hold the call must be active. 2. 9. 6 Connecting calls You can initiate a three-party conference or connect calls from an existing wait list. Conference with active newly initiated call in mode 2 Press in sequence the consultation keys "R" twice to make a connection as described in chapter 2. 1. Press the menu key once as described for a conference connection with the call on hold and the newly initiated call. Connecting a conference from the wait list in mode 1 Press the menu key in mode 1 to set up a three party conference. You can set up a conference between the active call and the call on hold. Ending a conference There are two options to end the conference: Leave conference If you want to leave the conference without interrupting the connection between the two other existing calls, replace the handset, or press the Loudspeaker key if you are using hands-free, or the space key if you are using a headset. If you want to end the conference, press the arrow down key, the menu key or the clearing key. The calls then return to their previous position. End conference Note 1: If there are no other calls in the wait list, then "conference" and "conference finished" are displayed on the screen. Operating Manual IP Telephone SO9020 - 17 -- 17 - Note 2: Instead of menu key, it is also possible to press the consultation key "R" and "3". Connecting calls You can connect the active call with the call on hold by replacing the handset, pressing the Loudspeaker key or the Space key. 3. 1. 2 Send message using Indirect dialling It is faster to send messages using indirect dialling than by using the menu. Proceed as follows from idle state: First enter the name or number of the message recipient. Press the menu key to reach the special menu Indirect dialling (see chapter 9. ). Select the menu item Send message with the adjacent function key. Enter your text message; the recipient's number has already been selected. Send the message by pressing the menu key. OK on the display shows you the message has been sent successfully. Operating Manual IP Telephone SO9020 - 20 -- 20 - 3. 2. Receiving messages It is also possible to receive messages on the SO9020. It depends what mode your telephone is in, as to how you receive a message from another subscriber. The following chart explains which modes allow you to receive messages and how they are displayed. In idle state The message is shown directly on the display in this mode. [. . . ] The innovaphone Wiki at wiki. innovaphone. com should also be observed for configuration of the IP telephones. All instructions specified there should be followed carefully and the devices should only be used in accordance with these instructions. Note: Please note the following instructions for your own safety: Power supply The external power supply is designed for operation with a 100-240 V, 50 Hz AC mains network. Never try to connect the equipment to other mains systems! [. . . ]