User manual ROWENTA STEAM BRUSH STEAM N PRESS DA70

[. . . ] Always disconnect appliance from electrical outlet when filling appliance with water, emptying appliance or when not in use. Do not operate appliance with a damaged cord or if the appliance has been dropped or damaged. To avoid the risk of electric shock, do not disassemble the appliance, ship it to the nearest authorized Rowenta Appliance Service Center for examination and repair. Incorrect reassembly can cause a risk of electric shock when the appliance is used. [. . . ] Never set the voltage selector to 120 V in a 220­240 V supply, as this can damage the product. FILLING THE WATER TANK Before plugging in the Steam 'n Press fill the water tank (C) with water as follows: Remove the water tank To remove the water tank, hold on to the bottom half of the handle and slide the top half of the handle away from the appliance as shown. 5 Filling the water tank Remove cap, fill the tank with ordinary tap water and close the cap. Replacing the water tank Put the full water tank back into the unit, by sliding the lower handle back into the top half of the handle until it is firmly in place. Adding water during use Always unplug the appliance and wait for it to cool down before removing the water tank. Handle with care as unit will remain hot for a considerable time. Fill as indicated in water tank filling section. Plug in the appliance and wait approximately one minute to ensure your Steam 'n Press is fully reheated before using it. ATTACHING AND REMOVING THE SOLEPLATE COVER Attaching the soleplate cover The Steam 'n Press should be unplugged and completely cool when removing or attaching the soleplate cover. To attach the soleplate cover (K) to the Steam 'n Press, hold the soleplate cover by the ribbed finger grips (J) and slide the cover over the soleplate. Turn the soleplate cover lock (G) half a turn (180°) to the left to lock the soleplate cover into position. Your appliance can be used as a Steambrush once cover is attached. Reference "Steambrush Function" section of instructions for further use information. 6 Removing the soleplate cover The steambrush should be unplugged and completely cool when removing or attaching the soleplate cover. To remove the soleplate cover (K) turn the soleplate cover lock (G) a half turn (180°) to the right. Grip the soleplate cover by the ribbed finger grips (J) on both sides as shown and pull towards the tip of unit to remove. Reference "Ironing Function" section of instructions for further use information. IRONING FUNCTION The soleplate of the Steam 'n Press will smooth out tough wrinkles from clothes and press in sharp creases and pleats. Starting up ! Before plugging in please remove cover. When the Steam 'n Press is plugged in the soleplate heats. Do not touch or remove the soleplate cover without letting the soleplate cool down. Remove the soleplate cover as indicated in instructions called "Removing the Soleplate Cover". Plug in the appliance, place it on its side and wait approximately one minute for it to reach full temperature before using. During use or while unit is heating or cooling, do not rest it on its soleplate. Place product on its side on a firm flat surface, as it will be hot. ! Never iron clothes while they are being worn. 7 Selecting the temperature Set the thermostat control dial (A) according to the type of fabric you are ironing. Check the fabric label for the appropriate setting. Fabric synthetics nylon polyester silk wool cotton linen Temperature regulator q (low temperature) qq (medium temperature) qqq (high temperature) Start at low temperature q and graduate to high temperature q q q. For delicate fabrics we recommend carrying out a test on an unobtrusive part of the garment (inner seam). Steam can only be produced when the thermostat is aligned to q q q setting. STEAMBRUSH FUNCTION Using for the first time ! min n mi When the Steam 'n Press is plugged in the soleplate heats. Do not touch or remove the soleplate cover without letting the soleplate cool down. Make sure soleplate cover is securely in place before using the steambrush function. Please reference section in instructions called "Attaching the Soleplate Cover". [. . . ] However, some types of softeners, particularly those that use chemicals such as salt, can cause the appliance to leak or spit during use. If you experience this type of problem, we recommend that you try using inexpensive bottled spring water or untreated tap water. Once you have changed water it will take several uses to correct the problem. Rowenta recommends trying the steam function for the first time on an old towel or cloth to avoid damaging your clothes. [. . . ]